Problems with ST585? List here

[xingkia]

Hi guys, i gt a 585v6 2 weeks ago from singnet.. now i got a very weird problem.. everytime i go bnet play dota it will get d/c from the game (lag out). but my internet connection is still there.. any1 experience the same problem or gt solution for it? my firmware version is 5.3.8.0.0. Thx

[chaicka]

Well, basically, if ur line is on the Hua Wei DSLAMs, it's preferably changed, be it ADSL or ADSL2+...it's meant for compatibility with the DSLAM, not so much on the profile of the line/service.

However, I may be wrong, since I still do not have a good insight on what these 3 particular registers do...so, for sure, ADSL2+ confirm must put in, for ADSL, depends on what DSLAM ur line is on and worth giving it a try if it's on Hua Wei ADSL2+ DSLAM.

How to identify? Should be quite easy...based on limited knowledge, these Hua Wei DSLAMs are one of the two brand of ADSL2+ DSLAMs which uses Globespan (GSPN) chipset. None of the precedence ADSL DSLAM uses GSPN chipset. So, check the Vendor/Chipset that shows in ur CPE's line info. For SpeedTouch, it's under Broadband Connection | DSL Connection | Details.

[chaicka]

Hi guys, i gt a 585v6 2 weeks ago from singnet.. now i got a very weird problem.. everytime i go bnet play dota it will get d/c from the game (lag out). but my internet connection is still there.. any1 experience the same problem or gt solution for it? my firmware version is 5.3.8.0.0. Thx
Upgrade to R5.4.0.11 or R5.4.0.14 firmware, then make sure that modemoption is in the configuration as per posted in page 50 of this thread.

Make sure u grab the correct R5.4.0.11 or R5.4.0.14 firmware meant for ST585v6. It's available...
If u know the site I have mentioned in this forum numerous times, u know where to get it le...:)

[alvin81]

Upgrade to R5.4.0.11 or R5.4.0.14 firmware, then make sure that modemoption is in the configuration as per posted in page 50 of this thread.

Make sure u grab the correct R5.4.0.11 or R5.4.0.14 firmware meant for ST585v6. It's available...
If u know the site I have mentioned in this forum numerous times, u know where to get it le...:)

Thanks for ur info. Whatever things u mentioned no matter big or small or limited, it has helped alot for me.

Y not ask him to flash its to the R6 version? Anyway, I am a big fan of that site... checked it once every week to check for new firmwares. :)

[xingkia]

Upgrade to R5.4.0.11 or R5.4.0.14 firmware, then make sure that modemoption is in the configuration as per posted in page 50 of this thread.

Make sure u grab the correct R5.4.0.11 or R5.4.0.14 firmware meant for ST585v6. It's available...
If u know the site I have mentioned in this forum numerous times, u know where to get it le...:)

Erm.. if i upgrade the warranty still there?
Anyway i found the files but i dont know wat to do with them.. lol.
Thx

[alvin81]

The ..... stands for the rest of the :00:00:00.....too long to remember how many of them le...juz modify the cfg file's statement "modemoption=00:06:03:01:00:....the rest leave it as it is. The crucial key factor is the register 2nd to 4th.

Although the modemoption can be modified via CLI, but the command to do so is not specified, thus the best way is to edit the cfg file, and nothing should go wrong.

There is a tool, which I am evaluating now...seems to be a good tool, and quite foolproof. I think I saw someone posted it b4...

To change the modemoption register via CLI, go to ADSL CONFIG command then type MODEMOPTION=00:06:03:01:00:........

Just found the command on the CLI guide. Hope it helps. :)

[archbishopchia]

Eh i using 585i given by singnet firmware 5.3.8.0.0.

The method i use to create bnet games is to assign a public ip for the device then in game applications i added in warcraft 3 the default 6112 thing. Is that the correct way?

Should i update my firmware to 5.4 or the newer 6.1. Will it result in any problems? Must i reconfigure all the wireless settings?

[chaicka]

Thanks for ur info. Whatever things u mentioned no matter big or small or limited, it has helped alot for me.

Y not ask him to flash its to the R6 version? Anyway, I am a big fan of that site... checked it once every week to check for new firmwares. :)

There is no R6.1.0.5 firmware for ST585, only for ST585v6, and there has been reported issues with it, which may indicate unstability. I dun normally recommend something that is not really proven good unless the person on the other end is savvy enuf to know what he is doing and how to troubleshoot and post his findings or solutions to bugs later. :)

[chaicka]

Eh i using 585i given by singnet firmware 5.3.8.0.0.

The method i use to create bnet games is to assign a public ip for the device then in game applications i added in warcraft 3 the default 6112 thing. Is that the correct way?

Should i update my firmware to 5.4 or the newer 6.1. Will it result in any problems? Must i reconfigure all the wireless settings?
There is no ST585i....only ST585 or ST585v6...depending on when u got it. Recent month is ST585v6.

[chaicka]

To change the modemoption register via CLI, go to ADSL CONFIG command then type MODEMOPTION=00:06:03:01:00:........

Just found the command on the CLI guide. Hope it helps. :)
Oh...is it?

Must go back and try...coz in 5.3.x.x I dun recall it being able to be changed...or my memory failing me le...:D

[flameblade]

The ..... stands for the rest of the :00:00:00.....too long to remember how many of them le...juz modify the cfg file's statement "modemoption=00:06:03:01:00:....the rest leave it as it is. The crucial key factor is the register 2nd to 4th.


Hi, for the above command, it's already inside without me changing anything when i type "adsl config" in the CLI.

http://img185.imageshack.us/img185/5249/1232kv.th.jpg (http://img185.imageshack.us/my.php?image=1232kv.jpg)

[xingkia]

http://img487.imageshack.us/my.php?image=problemdota1lg.jpg

my stats here.
anyone know wat's wrong with my connection..

[chaicka]

Hi, for the above command, it's already inside without me changing anything when i type "adsl config" in the CLI.

http://img185.imageshack.us/img185/5249/1232kv.th.jpg (http://img185.imageshack.us/my.php?image=1232kv.jpg)
It's there coz it's part of SingNet's template in ST585...but there are pple who flashed generic firmware and use the inbuild wizard to cleanly create new setup, that's when that modemoption will go missing.

[chaicka]

alvin81,

Juz tried, it dun work leh...

=>adsl config only display out the settings, but dun allow changing the modemoption value...

what firmware u using?

[alvin81]

alvin81,

Juz tried, it dun work leh...

=>adsl config only display out the settings, but dun allow changing the modemoption value...

what firmware u using?

Hi chaicka, I'm using the latest firmware. I also didn't try. I just read it off from the CLI guide. Sorry if it doesn't help. Paiseh... :s34:

[chaicka]

Hi chaicka, I'm using the latest firmware. I also didn't try. I just read it off from the CLI guide. Sorry if it doesn't help. Paiseh... :s34:
Well, u misinterpret the CLI Guide.....coz it is clearly stated in both CLI Guide R5.4.0.14 as well as R6.1.0.5 that the options available are opermode and trace only. The modemoption is shown as example of the display of the configuration, nothing else.

To conclude, modemoption is only changable via editing the configuration file.

[alvin81]

Well, u misinterpret the CLI Guide.....coz it is clearly stated in both CLI Guide R5.4.0.14 as well as R6.1.0.5 that the options available are opermode and trace only. The modemoption is shown as example of the display of the configuration, nothing else.

To conclude, modemoption is only changable via editing the configuration file.

Got it. Thanks for the enlightenment! :) Again.. paiseh for the error.

[chaicka]

Anyone interested to swap a ST585v6 with my spare ST585?

Interested to take a look at what's new in R6.1.0.5 as well as compare between ST585 and ST585v6.

[RallyART®]

Well, u misinterpret the CLI Guide.....coz it is clearly stated in both CLI Guide R5.4.0.14 as well as R6.1.0.5 that the options available are opermode and trace only. The modemoption is shown as example of the display of the configuration, nothing else.

To conclude, modemoption is only changable via editing the configuration file.

..edited..see post below

[RallyART®]

Well, u misinterpret the CLI Guide.....coz it is clearly stated in both CLI Guide R5.4.0.14 as well as R6.1.0.5 that the options available are opermode and trace only. The modemoption is shown as example of the display of the configuration, nothing else.

To conclude, modemoption is only changable via editing the configuration file.

Edited...sorry have to take down the post. just to say it can be done via CLi and need not be from the config file.

[alvin81]

Edited...sorry have to take down the post. just to say it can be done via CLi and need not be from the config file.

So whats the command to edit it via CLI?

[alvin81]

Anyone knows if I am able to add in custom firewall rules into the ST585? I would like it to allow MSN Messenger but I can't seems to add the rule into the firewall. I don't want to assigned it under the 'applications'.

[gray]

Apologies for sounding amateurish but have been out of touch of the ST 585 scene for a while.

Have been using firmware 5.3.2.6 under Generic PPPoE/PPPoA (modified by user) since day 1. Recently, the SN Margin (Up/Down) numbers seems to be worsening compared to before and I am experiencing higher CRC errors. Was thinking whether a firmware might be of any value.

Have been thrudging through the recent posts in this thread and it seems that the 5.4.X.X firmware is the recommended flavour of the month for the ST 585.

Am wondering whethering would upgrading the firmware to 5.4.x.x would be a good idea in my case. As I am NOT an advanced user and would prefer an upgrade that is less painful and hopefully not requiring advanced technical troubleshooting skills given I have almost none. Appreciate any firmware suggestions.

[chaicka]

Anyone knows if I am able to add in custom firewall rules into the ST585? I would like it to allow MSN Messenger but I can't seems to add the rule into the firewall. I don't want to assigned it under the 'applications'.

MSN Messenger dun even need port forwarding or firewall rules to be added, as it works seamlessly with the build in ALG.

[alvin81]

MSN Messenger dun even need port forwarding or firewall rules to be added, as it works seamlessly with the build in ALG.

Sorry... whats ALG? I tried sometime ago that if I don't forward the port, both sending and receiving speed will be very slow.

[chaicka]

Sorry... whats ALG? I tried sometime ago that if I don't forward the port, both sending and receiving speed will be very slow.
Search the forum...I believe ALG has been described/explained b4...as it's a rather old technology which is available in almost every broadband router u can find nowadays.

Mine work fine without any port forwarding, and I dun use UPnP at all too. It is even compatible with Messenger Live.

[gray]

Apologies for sounding amateurish but have been out of touch of the ST 585 scene for a while.

Have been using firmware 5.3.2.6 under Generic PPPoE/PPPoA (modified by user) since day 1. Recently, the SN Margin (Up/Down) numbers seems to be worsening compared to before and I am experiencing higher CRC errors. Was thinking whether a firmware might be of any value.

Have been thrudging through the recent posts in this thread and it seems that the 5.4.X.X firmware is the recommended flavour of the month for the ST 585.

Am wondering whethering would upgrading the firmware to 5.4.x.x would be a good idea in my case. As I am NOT an advanced user and would prefer an upgrade that is less painful and hopefully not requiring advanced technical troubleshooting skills given I have almost none. Appreciate any firmware suggestions.


Anybody can help on the above?

[ultimax]

Tried 5.4 bf but later switch back to 5.3.8. I find v5.4 not very stable in getting max speed.
You can get v5.3.8(approve by Singnet) from VRNET if you want it.

[aristein]

Will the expertise here tell me if there is anything wrong with my line. Am on Singnet 1500 using ST585, damn slow man

DSL Connection

Link Information


Uptime: 2 days, 2:12:50

Modulation: G.992.1 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 448 / 3.488

Data Transferred (Sent/Received) [MB/MB]: 85,48 / 439,04

Output Power (Up/Down) [dBm]: 0,5 / 13,5

Line Attenuation (Up/Down) [dB]: 9,0 / 26,0

SN Margin (Up/Down) [dB]: 9,0 / 29,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 44 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 158 / 0

HEC Errors (Up/Down): 66 / 0

[zetaphonx84]

Hhhhmm was reading quite a few pages oh this thread but seriously as i m super noob abt internet n router n nv own 1 b4 lol. I seriously dun understand quite alot of tings. perhaps maybe next next Wednestday when i get my hands on e router. i wil start to understand abit le~

[alvin81]

Can anyone advise me what is "Subnet Directed Broadcasts" and how to enable and disable it on the ST585?

I am trying to send a magic packet thru the internet from a remote connect to wake my home pc (so that I can use PcAnywhere to do remote control). I have done the appropriate port forwarding. But the only thing stopping me now is the "Subnet Directed Broadcasts" setting.

I am using Depicus' Wol for Windows to send the magic packet. This is the link to the Depicus (http://www.depicus.com/wake-on-lan/wake-on-lan-gui.aspx) website.

Can anyone advise pls. TIA! :)

[ultimax]

Will the expertise here tell me if there is anything wrong with my line. Am on Singnet 1500 using ST585, damn slow man

DSL Connection

Link Information


Uptime: 2 days, 2:12:50

Modulation: G.992.1 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 448 / 3.488

Data Transferred (Sent/Received) [MB/MB]: 85,48 / 439,04

Output Power (Up/Down) [dBm]: 0,5 / 13,5

Line Attenuation (Up/Down) [dB]: 9,0 / 26,0

SN Margin (Up/Down) [dB]: 9,0 / 29,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 44 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 158 / 0

HEC Errors (Up/Down): 66 / 0

Seem alright with me except that I never get HEC error bf.

[zetaphonx84]

hhmm was searching the forum but can only find a thread on how to turn 2wire 2700 to bridge mode. But cant find a thread on turning ST 585 to bridge? Can any1 guide me please? thou i haven get it now haha.. but rather super anxious to noe :) will be getting on friday :) wee~~

[speedknight]

got this modem over from shinji_U ejoying it now! less promatic that all my previous modem like

-Tecom AR1201 ADSL ethernet(Compliments of Singnet during first signed up)+netgear WGR614v5 wireless router(brought 1st hand $69)

-2Wire 1800HG ADSL Wireless+router(Compliments of Singnet during recontract/Sold)

-Siemens Speedstream4100(brought 2nd hand for $20)+netgear WGR614v5 wireless router



man i love this modem



problem is abit diffuclt to configure

[chaicka]

got this modem over from shinji_U ejoying it now! less promatic that all my previous modem like

-Tecom AR1201 ADSL ethernet(Compliments of Singnet during first signed up)+netgear WGR614v5 wireless router(brought 1st hand $69)

-2Wire 1800HG ADSL Wireless+router(Compliments of Singnet during recontract/Sold)

-Siemens Speedstream4100(brought 2nd hand for $20)+netgear WGR614v5 wireless router



man i love this modem



problem is abit diffuclt to configure
It's not that difficult...the GUI is more structured...and that's common across enterprise/business level products (structured GUI) while soho-class are mostly messy, unstructured.

Oh, btw, since u have the SS4100 and not in use, care to pass it to me so that I can attempt to unleash it from the crippled firmware?

[speedknight]

It's not that difficult...the GUI is more structured...and that's common across enterprise/business level products (structured GUI) while soho-class are mostly messy, unstructured.

Oh, btw, since u have the SS4100 and not in use, care to pass it to me so that I can attempt to unleash it from the crippled firmware?someone bidded for it @ $20 liaoz..... so how?

eh lets not ot this thread contact me via:

sabretoothx@hotmail.com

or

91377803

[leaving_footsteps]

I noticed that all my settings (port forwarding etc) are lost whenever I use the connection wizard to change password. Is there anyway to solve this?

[chaicka]

I noticed that all my settings (port forwarding etc) are lost whenever I use the connection wizard to change password. Is there anyway to solve this?
The wizard is merely a mechanism that generates a new configuration file using templates, thus anything not in the templates and not prompt to enter will not be written in the final output configuration file.

Which password are you referring to? The User Management GUI allows u to change the password (except the blank-name account which SingNet customized template uses).

[leaving_footsteps]

The wizard is merely a mechanism that generates a new configuration file using templates, thus anything not in the templates and not prompt to enter will not be written in the final output configuration file.

Which password are you referring to? The User Management GUI allows u to change the password (except the blank-name account which SingNet customized template uses).
The Singnet log in password. I can't seem to be able to edit the password without using the wizard.

[chaicka]

Let me confirm this at home...I recall it being editable once u logon with administrator rights, and it's under the broadband GUI menu portion.

[aristein]

hhmm was searching the forum but can only find a thread on how to turn 2wire 2700 to bridge mode. But cant find a thread on turning ST 585 to bridge? Can any1 guide me please? thou i haven get it now haha.. but rather super anxious to noe :) will be getting on friday :) wee~~


http://forums.hardwarezone.com/showthread.php?t=1375094&highlight=ST585

[leaving_footsteps]

Let me confirm this at home...I recall it being editable once u logon with administrator rights, and it's under the broadband GUI menu portion.
Thanks. I will try to look again too.

I am using "Administrator" too btw.

[alvin81]

I just got my ST585v6 last week. Will it be good to flash it to the latest firmware or just use SingNet's customised firmware?

[leaving_footsteps]

Help needed with ST585v6 at http://forums.hardwarezone.com/showthread.php?t=1404157

Port 80 forwarding problem.

EDIT: Resolved. However, if I access my wan ip from the network, I go to the ST585 page. Help?

[leaving_footsteps]

Is something wrong with my ST585v6? It's been the 3rd time my configurations are lost after powering down.

[chaicka]

Help needed with ST585v6 at http://forums.hardwarezone.com/showthread.php?t=1404157

Port 80 forwarding problem.

EDIT: Resolved. However, if I access my wan ip from the network, I go to the ST585 page. Help?
Go CLI, look for nat loopback, and set it enable. It should work, but no promises.

[leaving_footsteps]

Go CLI, look for nat loopback, and set it enable. It should work, but no promises.
Thanks for your help, more help needed though.

I telnet into ST585v6 and go into "nat".

What do I do to get nat loopback enabled?

Do I use "ifconfig"?

If yes,

intf = loop?
translation = ??? <- I tried to key in enabled and my connection to the ST585v6 will 'hang' until I restart it by powering it off/on.

[chaicka]

try searching this forum, while I try to dig my settings...I think I post the actual command b4...

Found the thread:
http://forums.hardwarezone.com/showthread.php?t=1178223&highlight=loopback

[leaving_footsteps]

try searching this forum, while I try to dig my settings...I think I post the actual command b4...

Found the thread:
http://forums.hardwarezone.com/showthread.php?t=1178223&highlight=loopback
Thank you very much. Everything works now.

Thanks again.

[chaicka]

Thank you very much. Everything works now.

Thanks again.
Welcome.

Do help others in the forum, tat's all I ask for...coz I cannot forever be the only one wif all these knowledge and only one helping others...need more pple to share what I know and pass it on...

Nagging as usual...but hope more will help out...otherwise, great info get lost as pple move on wif their life.

[chaicka]

leaving_footsteps,

Disable that Web Browsing Interception...it will improve performance.

[leaving_footsteps]

leaving_footsteps,

Disable that Web Browsing Interception...it will improve performance.
Thx. I have disabled it.

Some non important issues here.

I was playing (thru telnet) around with it and saved a configuration file in it. Now I can't delete it (delete command only deletes user.ini). No priviledge to in FTP mode. Haha. Hands too itchy.

I tried to do a restore via the Web GUI and got all my settings lost.

BTW, how can I get to use PPPoA instead of PPPoE? I noticed a lot of PPPoA settings in the user.ini file. (Web GUI can only use PPPoE).

[chaicka]

Thx. I have disabled it.

Some non important issues here.

I was playing (thru telnet) around with it and saved a configuration file in it. Now I can't delete it (delete command only deletes user.ini). No priviledge to in FTP mode. Haha. Hands too itchy.

I tried to do a restore via the Web GUI and got all my settings lost.

BTW, how can I get to use PPPoA instead of PPPoE? I noticed a lot of PPPoA settings in the user.ini file. (Web GUI can only use PPPoE).
Shouldn't be...u can delete any config files coz they are saved in a directory that allows deletion.
U mentioned no FTP, means u using SingNet firmware?

PPPoA mode, u can either use the Web GUI wizard, else u can use the residential CD (can download from my mirror if u dun have it).

[leaving_footsteps]

Shouldn't be...u can delete any config files coz they are saved in a directory that allows deletion.
U mentioned no FTP, means u using SingNet firmware?

PPPoA mode, u can either use the Web GUI wizard, else u can use the residential CD (can download from my mirror if u dun have it).Yes. I am using Singnet firmware 5.3.8.0.

I noticed that some guys here flashed their ST585 with non Singnet firmwares. But I am not sure if those will work for ST585 version 6 (which I think is a reduced/cost cutting version).

I can get into FTP but don't even has rights to do a list.

I tried to "delete filename" while in telnet, but the command doesn't accept filename (ironically, the save configuration command asked for a filename). "delete" will delete the user.ini

No option to use PPPoA in the wizard BTW.

[chaicka]

There are 2 separate sets of firmwares, one set is for ST585, and the other set is for ST585v6.
Firmwares for ST585 stopped at R5.4.0.14, while for ST585v6, it's at R6.1.0.5.

Listing is only allowed on a particular directory, not the whole ftp server. :D
If u are keen, I can let u know the directory. But it's not meant for generic public least they screwed up the SpeedTouch CPEs and later give the vendor troubles, which I want to avoid at all cost.

Looks like ST585v6 with SingNet firmware is locked down. But still, all u need is juz the residential CD (generic) to configure it to PPPoA, without the need to flash the firmware at all.

[leaving_footsteps]

There are 2 separate sets of firmwares, one set is for ST585, and the other set is for ST585v6.
Firmwares for ST585 stopped at R5.4.0.14, while for ST585v6, it's at R6.1.0.5.

Listing is only allowed on a particular directory, not the whole ftp server. :D
If u are keen, I can let u know the directory. But it's not meant for generic public least they screwed up the SpeedTouch CPEs and later give the vendor troubles, which I want to avoid at all cost.

Looks like ST585v6 with SingNet firmware is locked down. But still, all u need is juz the residential CD (generic) to configure it to PPPoA, without the need to flash the firmware at all.
I will use the CD (hope this CD is the one you mentioned) that comes with it then.

It's probably better than I don't know about the directory, I have real itchy hands. :D

[chaicka]

I will use the CD (hope this CD is the one you mentioned) that comes with it then.

It's probably better than I don't know about the directory, I have real itchy hands. :D
Nope, I doubt the CD they provided has all the templates...:D
You should know where to get the CD I mentioned...juz follow my postings.

[leaving_footsteps]

Nope, I doubt the CD they provided has all the templates...:D
You should know where to get the CD I mentioned...juz follow my postings.Found the CD :D Thanks.

I found the new firmware too. Now my hands are really itchy. Is it advisable for me to upgrade the firmware?

EDIT: Using PPPoA now!

In case someone needs this info => VPI/VCI = 0.100

[chaicka]

Well, hope to see good news from u...tat PPPoA is more stable. :)

[pakthedude]

Just got my 2Wire 2700HG exchange for the ST585v6

The firmware is 5.3.8.0.0

Is there any firmware update and is it recommended to upgrade for Singnet 10Mbps?

Is there any way to set the region in Wireless Access Point to ASIA instead of the default Europe?

[Alphas]

is there any command to increase the wireless strength of the ST585?

[chaicka]

is there any command to increase the wireless strength of the ST585?
Inside CLI.

[Alphas]

even I had the 800 over pages of CLI, I m not gona read through them, there is just too much infomation.

[revmazza]

hi guys, im using the 585(i) v6, updated firmware to v6.1.0.5
hows my line? juz upgraded and using singnet 10Mb plan now

Link Information

Uptime: 0 days, 0:40:09

Modulation: G.992.5 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 1.031 / 13.980

Data Transferred (Sent/Received) [MB/MB]: 21,29 / 243,56

Output Power (Up/Down) [dBm]: 4,5 / 8,0

Line Attenuation (Up/Down) [dB]: 3,0 / 11,0

SN Margin (Up/Down) [dB]: 6,5 / 22,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 9 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 0 / 9

HEC Errors (Up/Down): 0 / 9


btw, port forwarding doesnt seem to work for me for the speedtouch (had no probs wif the 2wire when im still on my 3500 plan). yes, i know ive done it right... but BT still connect to local peers only. disabled the firewall thru telnet already as well. on wireless using a mac now and download speed from the NDP webbie reaches over 1400KB/sec sumtimes, so i know im on ADSL2+ rite. hope u guys can help! txs! :)

ps: ive read thru all the pages of this thread btw! hahaha

[chaicka]

Release Notes for R6.1.0.5 (http://download.yousendit.com/BDBDAAF040740D96)

Hope it helps those using SpeedTouch to understand what's been fixed or added in R6.1.0.5 firmware.

[chaicka]

Summarized:

#1: Line out of synch due to Impulsive Noise

Description:
A High CRC and FEC error on the SpeedTouch™585 and SpeedTouch™680, due to
Impulsive Noise caused the line to go temporarily out of synch, which in turn caused
the PPP connection to go down.

Solution:
The Impulsive Noise Protection was improved. Even when the line goes temporarily
out of synch, the PPP connection does not go down.

#2: Double ACK messages

Description:
Double ACK-messages were sent out, resulting in a loss of bandwidth.

Solution:
The issue has been resolved.

#3: Timed Reboot

Description:
Timed reboot has been added.

#4: DHCP Link-sensing

Description:
DHCP Link-sensing has been added. This means that the PPP link will stay up even
when lower layers are out of synch. In case of re-synch, the PPP link need not be
renewed.

#5: DSD Restriction

Description
When Website filtering is activated (online filtering and/or URL white- or blacklisting),
the maximum amount of simultaneous web-surfing TCP connections is around 20,
depending on the type of connection.

Workaround
If you need more users, set Web Browsing Interception to either, automatic mode i.e.
Web Browsing Interception will only be activated when the DSL or PPP is down, or
disable it altogether (set to disabled)

As an alternative, DSD can be disabled via the SpeedTouch™ web GUI.

#6: Broken backward compatibility between R5.4 and R6.1 DHCP configuration

Description:
The configured order of requested options in the DHCP client is important because it
determines the processing sequence in the DHCP client when the ack is received. As
the order of options has changed in software release R6.1, unpredicted behavior can
encounter when upgrading from software release R5.4 to R6.1.

Solution:
Reset your SpeedTouch™ to defaults and reconfigure.

[alvin81]

Release Notes for R6.1.0.5 (http://download.yousendit.com/BDBDAAF040740D96)

Hope it helps those using SpeedTouch to understand what's been fixed or added in R6.1.0.5 firmware.

Hi chaicka, do you mind reposting the release notes again pls? Thanks for your effort.

[chaicka]

http://mirror.opensourcehub.com/pub/speedtouch/routers/ReleaseNotes/E-DOC-CRN-20060308-0002_v1.0_public.pdf

[alvin81]

http://mirror.opensourcehub.com/pub/speedtouch/routers/ReleaseNotes/E-DOC-CRN-20060308-0002_v1.0_public.pdf

Thanks a million. Trying out the 6.1.9.6 now. :)

[Heron_Kusanagi]

DMZ doesn't work with more than 1 wired device...

EDIT: By that I mean that when I connect more than 1 device, I can't use DMZ.

[chaicka]

Thanks a million. Trying out the 6.1.9.6 now. :)
Keep me posted dude...

[Darren212]

Hi Guys ! Been reading this thread just before i got my ST585v6 and i finally got it a week ago!
Overall, i am satisfied with the 585 till recently i experienced some problems with it.

A Singnet guy came over to check the line yesterday and he says that my line is fine. Well, i hope so...

Here are 2 screenshots of log..

http://img169.imageshack.us/img169/4549/error1gr7.th.jpg (http://img169.imageshack.us/my.php?image=error1gr7.jpg)

http://img191.imageshack.us/img191/8171/error2he6.th.jpg (http://img191.imageshack.us/my.php?image=error2he6.jpg)

i am getting "xDSL linestate down" errors in my log and that disconnects my connection for a while before it comes back on... I also get high CRC and HEC errors...


It might be a faulty 585 and i thought of replacing it :sad:

Any solutions ? :s11:

Greatly Appreciated

[Darren212]

Bump! Need Help!

Heres another screenshot!

http://img152.imageshack.us/img152/8214/scary2hp1.th.jpg (http://img152.imageshack.us/my.php?image=scary2hp1.jpg)

[chaicka]

Check for interference...it appears that there is interference that invoke the DSL Sync drops...

If u read thru this thread, u know that there is even cases whereby due to power-on of a threadmill causing the interference and thus dsl sync drop.....so if u phone line is laid together wif power cord in the same trunking, or ur phone cord placed near a power adapter, etc...interference occurs.

[michael_thm]

Just wondering if it is common for Singnet 10Mbps to be connected for only 1 to 2 day only before your connection get reset? Asking because I could stay connected normally for more than a week with the same IP without reset when I was on Pacnet.

[gray]

Not entirely sure what has happened, I just did a fresh install of Win XP Pro, afterwhich, I tried to loging into my ST585 via speedtouch.lan using a new install of IE7, strangely enough, the login and password that I normally use does not work. Am pretty postive, I have keyed in correctly.

Would doing a hard reset help of the modem help? Any other options to consider? Appreciative of any pointers.

[Darren212]

Check for interference...it appears that there is interference that invoke the DSL Sync drops...

If u read thru this thread, u know that there is even cases whereby due to power-on of a threadmill causing the interference and thus dsl sync drop.....so if u phone line is laid together wif power cord in the same trunking, or ur phone cord placed near a power adapter, etc...interference occurs.

Hey Chaicka ! Thanks for the reply :)
i tried moving the 585 around the table, straighten the phone line, plugging the power adapter as far as possible but however, i still get the "xDsl linestate down" errors.
The phone line is rather long but i have made sure that along the way, no other cables or adapters are in the way..
I am wondering now, could it be that the 585 is faulty ?

Will do somemore tests first before changing it :( Looks like its a trial and error issue

[michael_thm]

Not entirely sure what has happened, I just did a fresh install of Win XP Pro, afterwhich, I tried to loging into my ST585 via speedtouch.lan using a new install of IE7, strangely enough, the login and password that I normally use does not work. Am pretty postive, I have keyed in correctly.

Would doing a hard reset help of the modem help? Any other options to consider? Appreciative of any pointers.

Nah nothing will work. It is a IE7 bug. Use other browsers to access your router page or downgrade back to IE6.

[chaicka]

Hey Chaicka ! Thanks for the reply :)
i tried moving the 585 around the table, straighten the phone line, plugging the power adapter as far as possible but however, i still get the "xDsl linestate down" errors.
The phone line is rather long but i have made sure that along the way, no other cables or adapters are in the way..
I am wondering now, could it be that the 585 is faulty ?

Will do somemore tests first before changing it :( Looks like its a trial and error issue
See if u can arrange for a line check.

2 mins and get 140 CRC, 111 HEC errors.....that's way too high.
Chance of ST585 being faulty to result in such errors is low...

[gray]

Nah nothing will work. It is a IE7 bug. Use other browsers to access your router page or downgrade back to IE6.

Thanks for the quick response, that explains alot, although it is still strange a browser's bug could affect the login.

Probably have to install Firefox then, cause my main browswer (Maxthon) no longer works as well since its shelled on top of whichever IE I have installed.

[gray]

Thanks for the quick response, that explains alot, although it is still strange a browser's bug could affect the login.

Probably have to install Firefox then, cause my main browswer (Maxthon) no longer works as well since its shelled on top of whichever IE I have installed.

Just installed Opera, and it works !!!

[Darren212]

See if u can arrange for a line check.

2 mins and get 140 CRC, 111 HEC errors.....that's way too high.
Chance of ST585 being faulty to result in such errors is low...

Thanx again for the quick reply :s13:

The Singnet guy already came down for a line check last Friday and he said that the line was fine. Well, as i mentioned in my first post regarding this matter, i hope that his judgement is correct :s22:

Currently using my old adsl modem and router :( The line not as "demanding" as ADSL2+ i guess haha

[chaicka]

If in ADSL also has errors, then it is definitely line.

[Darren212]

If in ADSL also has errors, then it is definitely line.

Mmm i rarely get disconnected when using the ADSL line.. its does happen out of the blues though... Is there any other way that i can test my line besides reading the errors from the log ?

If its the line then i guess the Singnet guy must have missed out something :s31:

[psyko]

I'm using ST585v6, I've configured the port forwarding already and my friends can access my websites hosted on one of my PCs. However, when I try to access my own website, I get directed to the CPE's configuration page (popup asking for username/password). I try another PC in the network, also same thing. Did I miss out anything when configuring the CPE?

=============

Problem solved. Need to access the CLI and enable IP NAT Loopback

[xl8080]

i also encounter same problems..after i reseted my modem...alot of CRC and HEC errors....anyway to solve?

[bingom]

Originally Posted by abcdef
Hi. I'm on SNBB 10mbps plan. I've just checked my ST585 webpage recently and found that
my Bandwidth (Up/Down) [kbps/kbps]: 1.039 / 13.980


Hi, my ST585 webpage is showing abt 13.9 too!....from a high of 23+!. I am on the 10M plan.

Does anyone on the 10M plan face the same?


thanks

[bingom]

Originally Posted by abcdef
Hi. I'm on SNBB 10mbps plan. I've just checked my ST585 webpage recently and found that
my Bandwidth (Up/Down) [kbps/kbps]: 1.039 / 13.980


Hi, my ST585 webpage is showing abt 13.9 too!....from a high of 23+!. I am on the 10M plan.

Does anyone on the 10M plan face the same?


thanks

upzzz....tks

[chaicka]

Originally Posted by abcdef
Hi. I'm on SNBB 10mbps plan. I've just checked my ST585 webpage recently and found that
my Bandwidth (Up/Down) [kbps/kbps]: 1.039 / 13.980


Hi, my ST585 webpage is showing abt 13.9 too!....from a high of 23+!. I am on the 10M plan.

Does anyone on the 10M plan face the same?


thanks
Nothing wrong with 13,980kbps...the profile has been downsized as the technical issue has been resolved, which was why the initial deployment all had the high downstream profile on their line.

13,980kbps is more than sufficient to provide the 10mbps service which u have signed up for.....

[psyko]

Can the ST585v6 be forced to use ADSL instead of ADSL2+?

I'm on the 10mbps ADSL2 plan.

[chaicka]

Can the ST585v6 be forced to use ADSL instead of ADSL2+?

I'm on the 10mbps ADSL2 plan.
If u are on ADSL2+ plan, why the need to force the CPE to operate in ADSL?
ADSL mode will not be able to go beyond 8mbps.

[psyko]

Because ADSL2 is more sensitive towards noise right? I'd like to see if I can get better stability with ADSL. Remember my problem? I haven't had time to rewire the lines yet so I want to explore other alternatives in the mean time.

Downloads speeds not so crucial for me. 8mbps is good enough. I signed up for 10mbps is for the upload speed in the first place. :D

[alanchia67]

not sure can it be forced down to ADSL sync, but if you have a ADSL modem definitely you can surf at max 8Mbps on your existing line. of course, assuming the condition is stable enough to sustain it.

[chaicka]

Because ADSL2 is more sensitive towards noise right? I'd like to see if I can get better stability with ADSL. Remember my problem? I haven't had time to rewire the lines yet so I want to explore other alternatives in the mean time.

Downloads speeds not so crucial for me. 8mbps is good enough. I signed up for 10mbps is for the upload speed in the first place. :D
So far, SpeedTouch does not has a dedicated ADSL mode. I believe it's likewise for most of the soho ADSLx gateway routers.

Oh, there is a dedicated ADSL2 mode, which u may wanna give it a try to see if it can force down and stabilize.

[psyko]

There were 4 options for me, multimode, multi_adsl2, multi_readsl2, multi_adsl2plus (default).

multi_adsl2 & multi_readsl2 didn't work. The DSL LED keeps blinking for a few times and then the modem rebooted itself. Guess this doesn't work.

[sirandy8]

Hello All,

I've read thru quite a bit of this thread, but I'm still quite blur! I'm setting up a IP Cam, I can see the cam if I used the internal IP, say, 192.168.1.18. But I cannot assess it from outside using the 202.12..... or if I type in the domain name that is registered in ddns. I already have the loopback enabled. Did I miss out anything?

http://img221.imageshack.us/img221/6884/maplist1ln8.gif (http://imageshack.us)

[chaicka]

There were 4 options for me, multimode, multi_adsl2, multi_readsl2, multi_adsl2plus (default).

multi_adsl2 & multi_readsl2 didn't work. The DSL LED keeps blinking for a few times and then the modem rebooted itself. Guess this doesn't work.

Haiz...no choice...so far, most ADSL2+ CPEs I have seen dun offer a dedicated ADSL mode.

[danwee]

I'm having a strange problem and have not seen it reported anywhere. My router is the ST585v6 (hence this thread) with firmware 6.2.15.5. I have the firewall disabled (through CLI). When I connect to the router via 802.11b/g (PDA) I can access stuff on the LAN (such as the router's admin page). However, I cannot access stuff on the Internet. With my wired connections however, there is no such problem.

I've gone over the CLI pages and just can't seem to see anything wrong. Hostmgr seems to show everything is setup correctly. Does anyone else have this problem? wlif1 is configured similarly to the ethif interfaces.

The PDA has no problems with other routers and getting through those to the Internet so I don't think it's the PDA's configuration.

Would appreciate any help on this. TIA.

Daniel

[chaicka]

I'm having a strange problem and have not seen it reported anywhere. My router is the ST585v6 (hence this thread) with firmware 6.2.15.5. I have the firewall disabled (through CLI). When I connect to the router via 802.11b/g (PDA) I can access stuff on the LAN (such as the router's admin page). However, I cannot access stuff on the Internet. With my wired connections however, there is no such problem.

I've gone over the CLI pages and just can't seem to see anything wrong. Hostmgr seems to show everything is setup correctly. Does anyone else have this problem? wlif1 is configured similarly to the ethif interfaces.

The PDA has no problems with other routers and getting through those to the Internet so I don't think it's the PDA's configuration.

Would appreciate any help on this. TIA.

Daniel
Did u correctly disable to firewall, or in turn disabled the NAT?

Btw, make sure u disable the web browser interception feature. It hinders performance and sometimes, NAT sessions.

[danwee]

Yes, I believe I disabled the firewall and not the NAT. I have also disabled web interception. In any case, I decided to switch over to PPPoA and re-do everything - ie. disable firewall etc. and now it is working. The other thing I did differently is that now I am using the default router address 192.168.1.254 whereas before I had it set to 192.168.1.1. It may be due to that too but I'm too lazy to try it right now. I can imagine that some of the routes was hard wired for the default address. Thanks for the response.

Daniel

[chaicka]

Yes, I believe I disabled the firewall and not the NAT. I have also disabled web interception. In any case, I decided to switch over to PPPoA and re-do everything - ie. disable firewall etc. and now it is working. The other thing I did differently is that now I am using the default router address 192.168.1.254 whereas before I had it set to 192.168.1.1. It may be due to that too but I'm too lazy to try it right now. I can imagine that some of the routes was hard wired for the default address. Thanks for the response.

Daniel
Not necessary so...

When u mess around in CLI, alot of the chained settings do not get propagated automatically, thus need to make changes all over the places. That's my experience wif SpeedTouch CLI so far...(the residential series).

There is no hard-coding, thus most probably u miss some areas that need to be changed too.

Anyway, glad that it's working now. We can exchange pointers in the future.

[danwee]

Yes, I probably missed something. Actually that CLI interface is pretty cool - but you're right about the need to check the various settings for consistency. One example is the firewall - even when you disable it from the web GUI, it can be further disabled from the CLI - weird but that's just the way it is. Other than that, it seems quite alright and it's nice to be able to poke around under the hood just to see how things actually work.

Daniel

[alvin81]

I was just toying with the ST585v6 (6.1.9.6). Trying to get the syslog to work. I installed a kiwi syslog daemon on my desktop and tried to configure the router to send messages to my desktop via syslog.

The syslog can only be configured through CLI. The command is systemlog. From there, I followed the CLI guide but still can't get the syslog running. Whenever I entered the IP of my desktop as the destination to send the messages, it says "Destination address should be a net broadcast ip-address." I know when the last octect of an IP is 255, its an broadcast address but I don't think I can set my desktop to use that IP address (e.g. 192.168.1.255) right?

So my next step is to configure the router to send the messages to 192.168.1.255. Walla! I did see some messages appearing in the syslog server. So I did a "saveall" command and log off. But after that, the messages stop appearing on the syslog server.

Right now, I still can't get the system log to work properly. Any help?

Btw, anyone got the 6.2.15.5 firmware yet? I was able to get my hands on it from a source stated in this thread before. It seems that my connection suddenly became "slower" with the new firmware. I think maybe its my settings. Will try to see whats wrong. :s11:

[psyko]

I'm having high FEC (Up), what could be the cause? I'm using a ferrite core already.

Uptime: 7 days, 11:28:31
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 983 / 13.996
Data Transferred (Sent/Received) [GB/GB]: 3,40 / 3,25
Output Power (Up/Down) [dBm]: 6,5 / 1,5
Line Attenuation (Up/Down) [dB]: 4,0 / 11,0
SN Margin (Up/Down) [dB]: 6,0 / 21,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 3 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 2.579 / 0
FEC Errors (Up/Down): 4.290.070.272 / 0
CRC Errors (Up/Down): 660 / 252
HEC Errors (Up/Down): 400 / 156

[SakaeSushi]

Harlow to everyone

My boss just upgrade to the BizLink 2M line. but the problem now is i dunno how to configure my office firewall to work with the ST585. I have 16 public IP address.

Anyway. i set the IPOA to one with NAPT. Dunno issit this the reason i cannot add a public IP to my firewall.damn sad.

anyone can help help?? I dun want to waste the firewall since it has the anti spam thing...how to configure ST585 to the WAN1 port of my firewall??

[chaicka]

Harlow to everyone

My boss just upgrade to the BizLink 2M line. but the problem now is i dunno how to configure my office firewall to work with the ST585. I have 16 public IP address.

Anyway. i set the IPOA to one with NAPT. Dunno issit this the reason i cannot add a public IP to my firewall.damn sad.

anyone can help help?? I dun want to waste the firewall since it has the anti spam thing...how to configure ST585 to the WAN1 port of my firewall??
You should set the SpeedTouch to IPoA without NAPT. That should result in no NAT, no firewall (SpeedTouch inbuild). Then u need to set the WAN of ur Firewall to use one of the public ip address of the pool u have been assigned.

[chaicka]

I'm having high FEC (Up), what could be the cause? I'm using a ferrite core already.

Uptime: 7 days, 11:28:31
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 983 / 13.996
Data Transferred (Sent/Received) [GB/GB]: 3,40 / 3,25
Output Power (Up/Down) [dBm]: 6,5 / 1,5
Line Attenuation (Up/Down) [dB]: 4,0 / 11,0
SN Margin (Up/Down) [dB]: 6,0 / 21,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 3 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 2.579 / 0
FEC Errors (Up/Down): 4.290.070.272 / 0
CRC Errors (Up/Down): 660 / 252
HEC Errors (Up/Down): 400 / 156
FEC errors...which firmware u using?

[SakaeSushi]

You should set the SpeedTouch to IPoA without NAPT. That should result in no NAT, no firewall (SpeedTouch inbuild). Then u need to set the WAN of ur Firewall to use one of the public ip address of the pool u have been assigned.hey thanks chaicka for your quick reply...realli appreciate that.

firstly singtel gave me this

16 LAN IP
---------
58.185.X.X - 58.185.X.X+16
mask: 255.255.255.X

WAN IP
------
58.185.Y.Y(SingTel)
58.185.Y.Y(Customer)
mask: 255.255.255.Y

DNS servers
-----------
165.21.83.88
165.21.100.88

i tried to setup the firewall in No NAPT mode...but dunno why it wun connect to the net. the DSL will have a tick but it cannot get the DNS or or it says something like no ATM activity.

my ST585 got 4 eth port. so wat shd i do?? I should connect one of the eth port to the WAN port of my firewall??
in my firewall WAN address, i shd put 58.185.X.X?? then the mask put wat??

and one more question, how shd i utilise the 16IP they gave me?? for wat?? thanks in advance for your help.

I never study so advance networking before......but i am glad u willing to teach.

[chaicka]

hey thanks chaicka for your quick reply...realli appreciate that.

firstly singtel gave me this

16 LAN IP
---------
58.185.X.X - 58.185.X.X+16
mask: 255.255.255.X

WAN IP
------
58.185.Y.Y(SingTel)
58.185.Y.Y(Customer)
mask: 255.255.255.Y

DNS servers
-----------
165.21.83.88
165.21.100.88

i tried to setup the firewall in No NAPT mode...but dunno why it wun connect to the net. the DSL will have a tick but it cannot get the DNS or or it says something like no ATM activity.

my ST585 got 4 eth port. so wat shd i do?? I should connect one of the eth port to the WAN port of my firewall??
in my firewall WAN address, i shd put 58.185.X.X?? then the mask put wat??

and one more question, how shd i utilise the 16IP they gave me?? for wat?? thanks in advance for your help.

I never study so advance networking before......but i am glad u willing to teach.
First of all, this is not advance networking, it's the basics.

It seems u dun even know what the 16 ip addresses are, and how to use them. Thus, since it's a commercial deployment, pls engage consultation service.

[MrBuffet]

Harlow to everyone

My boss just upgrade to the BizLink 2M line. but the problem now is i dunno how to configure my office firewall to work with the ST585. I have 16 public IP address.

Anyway. i set the IPOA to one with NAPT. Dunno issit this the reason i cannot add a public IP to my firewall.damn sad.

anyone can help help?? I dun want to waste the firewall since it has the anti spam thing...how to configure ST585 to the WAN1 port of my firewall??

i charge $200/hr
pm if interested

[psyko]

FEC errors...which firmware u using?

I never touch/upgrade the firmware at all so:

Software Release: 5.3.8.0.0
Software Variant: AA
Boot Loader Version: 1.0.7
Board Name: BANT-W

[sunnyee]

Anyone using Explorer 7 to access the ST585 setting page. Mine cannot ?

[MrBean007]

Is there a problem with my connection..? a simple home networking

DSL Connection Details
DSL Line (Wire Pair): Line 1 (inner pair)
Protocol: G.DMT2+ Annex A
Downstream Rate: 3501 kbps
Upstream Rate: 795 kbps
Channel: Fast
Current Noise Margin: 19.1 dB (Downstream) 5.5 dB (Upstream)
Current Attenuation: 35.8 dB (Downstream) 18.9 dB (Upstream)
Current Output Power: 20.4 dBm (Downstream) -1.9 dBm (Upstream)
DSLAM Vendor Information: Country: {0xFF} Vendor: {GSPN} Specific: {0x1000}
PVC Info: 0/100

Internet Connection Details
Connection Type: PPPoE
Username:
Internet Address: 121.6.66.136
Subnet Mask: 255.255.255.255
Default Gateway: 219.74.222.1
Primary Domain Name Server: 165.21.100.88
Secondary Domain Name Server: 165.21.83.88
Domain:
Maximum Transmission Unit (MTU): 1492
Gateway Ping: Successful
DNS Communication: Successful
Configuration Server Post: Successful

[a10000]

Hi guys, um... are my stats ok for snbb 10mbps?
Uptime: 0 days, 0:04:05

Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 1.024 / 13.996
Data Transferred (Sent/Received) [KB/KB]: 0,00 / 0,00
Output Power (Up/Down) [dBm]: 2,0 / 1,5
Line Attenuation (Up/Down) [dB]: 0,5 / 16,0
SN Margin (Up/Down) [dB]: 6,5 / 16,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 34.078.720 / 0
CRC Errors (Up/Down): 8 / 0
HEC Errors (Up/Down): 0 / 0

Software Release: 6.2.15.5
Software Variant: AA
Boot Loader Version: 1.0.7
Product Code: 35942030
Board Name: BANT-W


I'm getting only 8mb results from speedtest.net, but can pull off 1.4mb consistant speed from fast download sites... i don't know if that's an issue or not. also, i was able to sync better, around 18mb in the past. then it slowed down to 13996 after flashing this firmware(if i'm not wrong) nothing works even if i restart it to factory settings and even downgrading the firmware... hope someone helps. thanks for reading

[chaicka]

Hi guys, um... are my stats ok for snbb 10mbps?
Uptime: 0 days, 0:04:05

Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 1.024 / 13.996
Data Transferred (Sent/Received) [KB/KB]: 0,00 / 0,00
Output Power (Up/Down) [dBm]: 2,0 / 1,5
Line Attenuation (Up/Down) [dB]: 0,5 / 16,0
SN Margin (Up/Down) [dB]: 6,5 / 16,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 34.078.720 / 0
CRC Errors (Up/Down): 8 / 0
HEC Errors (Up/Down): 0 / 0

Software Release: 6.2.15.5
Software Variant: AA
Boot Loader Version: 1.0.7
Product Code: 35942030
Board Name: BANT-W


I'm getting only 8mb results from speedtest.net, but can pull off 1.4mb consistant speed from fast download sites... i don't know if that's an issue or not. also, i was able to sync better, around 18mb in the past. then it slowed down to 13996 after flashing this firmware(if i'm not wrong) nothing works even if i restart it to factory settings and even downgrading the firmware... hope someone helps. thanks for reading
Add/Check the modemoptions= value in the configuration.
Search this thread...it's been mentioned the key to having any speedtouch CPEs to be compatible with the ADSL2+ DSLAMs in SG.

Oh, furthermore, most 10mbps service has a line profile approximately 13xxx kbps. It's normal. It used to be higher (>2xxxx kbps) becoz of technical issues/difficulties, which has been resolved and now, scaled back down to 13xxx kbps.

Anyway, FW 6.2.15.5 is not a stable firmware. Try the 6.2.16.3 or else, revert back to 5.4.14.0 which is a very stable firmware.

[a10000]

Hello chaicka... My ST585v6 totally malfunctioned after flashing it to 5.4.0.14... it's power led turned red with ethernet led flashing, can't access web interface, can't even startup the upgrade wiz now. Is there a way to solve this? I have tried resetting the modem but it doesn't work. Please help

[a10000]

OK, I got it back by doing the following: turning off the modem, turn on after 5 secs then hold down the restart button to set it back to kernel flash mode... the modemoptions you mentioned, i tried using this: 00060301000000000000000000000000 but it's still the same 8mbps result in speedtest, can you specify which to use?

[alvin81]

Add/Check the modemoptions= value in the configuration.
Search this thread...it's been mentioned the key to having any speedtouch CPEs to be compatible with the ADSL2+ DSLAMs in SG.

Oh, furthermore, most 10mbps service has a line profile approximately 13xxx kbps. It's normal. It used to be higher (>2xxxx kbps) becoz of technical issues/difficulties, which has been resolved and now, scaled back down to 13xxx kbps.

Anyway, FW 6.2.15.5 is not a stable firmware. Try the 6.2.16.3 or else, revert back to 5.4.14.0 which is a very stable firmware.

Agree with chaicka that the 6.2.15.5 is not stable. Downloaded and tried using if for a while. Didn't feel comfortable with it and there were some unfixed "bugs" mentioned in the release notes. Tried fooling around and manage to get the "change settings and modem reboot" bug to appear on my 585v6. =:p

[a10000]

Could someone send me a working user.ini? Or check which modemoption to use? Thanks

[hushpuppies]

Hi hi, I just recontracted from SNBB1500K to 10M using 585 v6. Want to check if my line stats are ok?
I read on this forum that for ADSL2+ the SN Margin should be within 5-7dB range? Is my SN margin acceptable then? Many Thanks! :)

Uptime: 0 days, 0:01:56
Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 1.019 / 13.996
Data Transferred (Sent/Received) [KB/KB]: 58,00 / 70,00
Output Power (Up/Down) [dBm]: 8,0 / 6,0
Line Attenuation (Up/Down) [dB]: 5,5 / 19,5
SN Margin (Up/Down) [dB]: 6,5 / 19,5
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 2 / 0
HEC Errors (Up/Down): 0 / 0

Product Name: ST585
Serial Number: CP0630JTDCS
Software Release: 6.2.16.3
Software Variant: AA
Boot Loader Version: 1.0.7
Product Code: 35942030
Board Name: BANT-W

And another question, if I use wireless with the ST585 in the same room, my speedtest results can never hit abv 10M but when using wire that is no problem. Is it my usb adpater's problem? I'm using linksys WUSB54GC.

[chaicka]

Hi hi, I just recontracted from SNBB1500K to 10M using 585 v6. Want to check if my line stats are ok?
I read on this forum that for ADSL2+ the SN Margin should be within 5-7dB range? Is my SN margin acceptable then? Many Thanks! :)

Uptime: 0 days, 0:01:56
Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 1.019 / 13.996
Data Transferred (Sent/Received) [KB/KB]: 58,00 / 70,00
Output Power (Up/Down) [dBm]: 8,0 / 6,0
Line Attenuation (Up/Down) [dB]: 5,5 / 19,5
SN Margin (Up/Down) [dB]: 6,5 / 19,5
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 2 / 0
HEC Errors (Up/Down): 0 / 0

Product Name: ST585
Serial Number: CP0630JTDCS
Software Release: 6.2.16.3
Software Variant: AA
Boot Loader Version: 1.0.7
Product Code: 35942030
Board Name: BANT-W

And another question, if I use wireless with the ST585 in the same room, my speedtest results can never hit abv 10M but when using wire that is no problem. Is it my usb adpater's problem? I'm using linksys WUSB54GC.
Wow...ur line is good.
Ignore the SNR Guideline of 5-7dB. That was valid when the line profiles are all >20mbps, but now, with lower line profiles of around 13+mbps, the SNR should be higher, in the range of 16-20dB.

Hmmm, FW 6.2.16.3, is it stable so far?

[hushpuppies]

Wow...ur line is good.
Ignore the SNR Guideline of 5-7dB. That was valid when the line profiles are all >20mbps, but now, with lower line profiles of around 13+mbps, the SNR should be higher, in the range of 16-20dB.

Hmmm, FW 6.2.16.3, is it stable so far?

My line is good ah? Ok trust you! :) I was worried because previously my 1500K has a lot of intermittent connection problems which SingNet never managed to fix it. The technican came down and said nothing was wrong with my line and modem. Hopefully with the new 585 and full replacement of all my MF, it will be ok. (I havent been surfing much yet on the new 10M plan)

Eh I just updated the firmware on Sunday..so far so good :s13:
Btw, thanks for ur site with the latest firmware n the upgrader. It is really useful.

[Webbyboy]

Recently having some problems. After the router modem is up for like 3-4 days, everything else can access like msn/irc and etc but only http websites can't be access at all...Tried proxy and no proxy but it can't work, only when i reboot the router modem then everything is fine again.. Using generic 5.4.0.14 firmware...anyone knows what's going on?

[chaicka]

My line is good ah? Ok trust you! :) I was worried because previously my 1500K has a lot of intermittent connection problems which SingNet never managed to fix it. The technican came down and said nothing was wrong with my line and modem. Hopefully with the new 585 and full replacement of all my MF, it will be ok. (I havent been surfing much yet on the new 10M plan)

Eh I just updated the firmware on Sunday..so far so good :s13:
Btw, thanks for ur site with the latest firmware n the upgrader. It is really useful.
Juz to be sure, update ur line stats again after a few days of having it on and usage.

[victory_loh]

i noticed the wireless security default is wep and when i configured it to wpa psk,my notebook has connection but i can't surf. anyone here pls help!

[ToOtWaI]

hi. would like to know what is the newest firmware usable for 585 with singnet BB now. I had seen R5 & R6 firmwares mention, but not much in detail on which to use.

[approvois]

DSL Connection

Link Information


Uptime: 0 days, 0:01:21

Modulation: G.992.5 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 1.024 / 20.519

Data Transferred (Sent/Received) [KB/MB]: 369,00 / 1,25

Output Power (Up/Down) [dBm]: 8,5 / 0,0

Line Attenuation (Up/Down) [dB]: 6,0 / 15,5

SN Margin (Up/Down) [dB]: 6,0 / 6,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 3 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 1 / 3

HEC Errors (Up/Down): 0 / 3


Hi Is the above stats okie? how come the output power down is 0?
i encounter frequent disconnection and not sure how to solve the problem? any idea?

[rasserie]

singtel should give u the mask for 16 lan ip.
if u cannot see it on the letter or email, its 255.255.255.240 for 16 lan ip.

as for ur wan side, if im not wrong, the mask is 255.255.255.252. pls check again ur letter from singtel. it should state clearly.
older config has mask of 255.255.255.0 with encap protocol of CIP and the singtel ip always ends with .2


firstly, since u applied for 16 lan ip which is routable, u normally shouldnt enable NAT. or else it will not work.

and ya, u realli are just getting only 14 usable IPs.
like what the experts here says, pls engage a professional consultant. it will save u from a lot of headache.


hey thanks chaicka for your quick reply...realli appreciate that.

firstly singtel gave me this

16 LAN IP
---------
58.185.X.X - 58.185.X.X+16
mask: 255.255.255.X

WAN IP
------
58.185.Y.Y(SingTel)
58.185.Y.Y(Customer)
mask: 255.255.255.Y

DNS servers
-----------
165.21.83.88
165.21.100.88

i tried to setup the firewall in No NAPT mode...but dunno why it wun connect to the net. the DSL will have a tick but it cannot get the DNS or or it says something like no ATM activity.

my ST585 got 4 eth port. so wat shd i do?? I should connect one of the eth port to the WAN port of my firewall??
in my firewall WAN address, i shd put 58.185.X.X?? then the mask put wat??

and one more question, how shd i utilise the 16IP they gave me?? for wat?? thanks in advance for your help.

I never study so advance networking before......but i am glad u willing to teach.

[rasserie]

if u are able to VPN in using st585, then u should have the latest firmware.

hi. would like to know what is the newest firmware usable for 585 with singnet BB now. I had seen R5 & R6 firmwares mention, but not much in detail on which to use.

[rasserie]

if u cannot surf, then u have no connection.

dun be fooled by the laptop saying that its connected and all.
try this, enter a wrong wep key and it will still say its connected. just that u are getting APIPA.

i noticed the wireless security default is wep and when i configured it to wpa psk,my notebook has connection but i can't surf. anyone here pls help!

[rasserie]

hey thanks chaicka for your quick reply...realli appreciate that.

firstly singtel gave me this

16 LAN IP
---------
58.185.X.X - 58.185.X.X+16
mask: 255.255.255.X

WAN IP
------
58.185.Y.Y(SingTel)
58.185.Y.Y(Customer)
mask: 255.255.255.Y

DNS servers
-----------
165.21.83.88
165.21.100.88

i tried to setup the firewall in No NAPT mode...but dunno why it wun connect to the net. the DSL will have a tick but it cannot get the DNS or or it says something like no ATM activity.

my ST585 got 4 eth port. so wat shd i do?? I should connect one of the eth port to the WAN port of my firewall??
in my firewall WAN address, i shd put 58.185.X.X?? then the mask put wat??

and one more question, how shd i utilise the 16IP they gave me?? for wat?? thanks in advance for your help.

I never study so advance networking before......but i am glad u willing to teach.
and oh ya, PVC is different from normal ADSL broadband.

[RurouniX]

Hi. Experiencing some weird user management related problems with my 585.

I have 4 computers connected to the 585, yet only one is able to get into the speedtouch GUI. The rest of them display some kind of HTTP denied error. Why is this so?

Also, how do you get the firmware changed?

Thanks.

[RurouniX]

:s12: :s12:

[RurouniX]

:s12: :s12:

[leaving_footsteps]

Are you using IE7?

[glacieraze]

Errr..
just to check if my line statics is ok anot


DSL Connection

Link Information


Uptime: 0 days, 1:04:33

Modulation: G.992.5 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 1.019 / 13.996

Data Transferred (Sent/Received) [MB/MB]: 5,34 / 38,99

Output Power (Up/Down) [dBm]: 4,5 / 0,0

Line Attenuation (Up/Down) [dB]: 3,0 / 11,0

SN Margin (Up/Down) [dB]: 6,0 / 22,0

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 2 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 2 / 2

HEC Errors (Up/Down): 0 / 0

cuz I encounter some slowness gaming experience

[leinad]

Need comments on this.

Someone cut my line recently (yes, as in, literally took a knife or scissors to cut it), and Singtel patched it back. Since then, I've been having a noisy line and my net connection has been dropping non-stop.

Here's my line stats. Should I be calling and asking for a senior tech to look at the line? I wonder if I can get them to rerun the line. It's not inside my house, but outside my house.

Uptime: 0 days, 0:11:53
Modulation: G.992.1 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 512 / 3,488
Data Transferred (Sent/Received) [MB/MB]: 1.75 / 5.48
Output Power (Up/Down) [dBm]: 11.5 / 19.5
Line Attenuation (Up/Down) [dB]: 23.0 / 36.5
SN Margin (Up/Down) [dB]: 23.0 / 30.0
Vendor ID (Local/Remote): TMMB / ALCB
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 13,038 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 0 / 3
HEC Errors (Up/Down): 0 / 3

/Dan

[megaweb]

hey thanks chaicka for your quick reply...realli appreciate that.

firstly singtel gave me this

16 LAN IP
---------
58.185.X.X - 58.185.X.X+16
mask: 255.255.255.X

WAN IP
------
58.185.Y.Y(SingTel)
58.185.Y.Y(Customer)
mask: 255.255.255.Y

DNS servers
-----------
165.21.83.88
165.21.100.88

i tried to setup the firewall in No NAPT mode...but dunno why it wun connect to the net. the DSL will have a tick but it cannot get the DNS or or it says something like no ATM activity.

my ST585 got 4 eth port. so wat shd i do?? I should connect one of the eth port to the WAN port of my firewall??
in my firewall WAN address, i shd put 58.185.X.X?? then the mask put wat??

and one more question, how shd i utilise the 16IP they gave me?? for wat?? thanks in advance for your help.

I never study so advance networking before......but i am glad u willing to teach.

This is megapop/bizlink setup. You need a special SpeedTouch CD assist you in the installation.

[_DeeK_]

Hello Guys, here are my line stats... The line has improved since the tech guys from Singnet came over to fix the internal wiring. However, when playing online games, I still get frequent disconnection.

The error is the usual "xDSL linestate down".

It goes down for about 30 secs and comes back up again... Any suggestions for improving the line ?

Uptime:0 days, 5:12:50
Modulation:G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]:975 / 13.996
Data Transferred (Sent/Received) [MB/MB]:80,14 / 156,25
Output Power (Up/Down) [dBm]:12,5 / 0,0
Line Attenuation (Up/Down) [dB]:8,5 / 21,0
SN Margin (Up/Down) [dB]:6,0 / 15,5
Vendor ID (Local/Remote):TMMB / GSPN
Loss of Framing (Local/Remote):0 / 0
Loss of Signal (Local/Remote):0 / 0
Loss of Power (Local/Remote):0 / 0
Loss of Link (Remote):0
Error Seconds (Local/Remote):414 / 0
FEC Errors (Up/Down):603.979.776 / 0
CRC Errors (Up/Down):4 / 229
HEC Errors (Up/Down):1 / 197

[_DeeK_]

Very bad experience today... Just when it rained, my line kept reconnecting iteself... xDSL linestate down and up... intervals about 30sec..

[chaicka]

Your Line is juz too noisy.
What's the firmware ur ST585 is using?

[_DeeK_]

Your Line is juz too noisy.
What's the firmware ur ST585 is using?Hi Chaicka, thanks for replying.

I am using the 5.3.8.0.0 firmware. What should i do ? Any suggestions?

[_DeeK_]

Any Suggestions ? =p

[misato]

From your line stats, it shows a "noisy" line.
You can do 2 things,

a. Check all your house phone point, make sure all connected phones goes through a micro-filter. Make sure the phone lines connected to your modem is in good condition and is securely connected to the modem socket and the micro-filter or wall socket. If in doubt of the cable condition, please change to a new one.

b. If a. dont improve anything, call singtel and tell them your line is noisy and have them arrange people to check and rectify any issue thats outside of your house.

[_DeeK_]

From your line stats, it shows a "noisy" line.
You can do 2 things,

a. Check all your house phone point, make sure all connected phones goes through a micro-filter. Make sure the phone lines connected to your modem is in good condition and is securely connected to the modem socket and the micro-filter or wall socket. If in doubt of the cable condition, please change to a new one.

b. If a. dont improve anything, call singtel and tell them your line is noisy and have them arrange people to check and rectify any issue thats outside of your house.Hey Misato, thanks for replying!

will do that when i get home today =p

They came the last time to check the line and they found trouble with the internal wiring. However, the guys did not check the lines outside the house. Not sure if this helps but i notice that when it rains, i tend to dc more often.
Will try step (a) and update back here

[_DeeK_]

This is the line stats when plugged in with another telephone cable.

Uptime: 0 days, 0:10:28
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 958 / 13.996
Data Transferred (Sent/Received) [MB/MB]: 1,42 / 3,27
Output Power (Up/Down) [dBm]: 12,5 / 0,0
Line Attenuation (Up/Down) [dB]: 8,5 / 21,0
SN Margin (Up/Down) [dB]: 7,5 / 16,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 1 / 0
HEC Errors (Up/Down): 0 / 0


The downstream SN Margin still high but like no errors! Is there any difference ?

[misato]

This is the line stats when plugged in with another telephone cable.

Uptime: 0 days, 0:10:28
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 958 / 13.996
Data Transferred (Sent/Received) [MB/MB]: 1,42 / 3,27
Output Power (Up/Down) [dBm]: 12,5 / 0,0
Line Attenuation (Up/Down) [dB]: 8,5 / 21,0
SN Margin (Up/Down) [dB]: 7,5 / 16,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 1 / 0
HEC Errors (Up/Down): 0 / 0


The downstream SN Margin still high but like no errors! Is there any difference ?
check the line stats again when you used for like 5hours, see if its the same.
take note of your line disconnection or loss of internet connectivities compare to previously see if the situation improve/degraded. If degrade, switch to another port and check again, if the variation from one socket to another is great, it means the source of trouble might really be your wiring.

On the site note, your "Line Attenuation" has very high values, meaning your quite far away from the DSLAM. You can call singnet to say your line is very unstable and is too far away from the DSLAM and request them to rewire to one close to your house.

[_DeeK_]

check the line stats again when you used for like 5hours, see if its the same.
take note of your line disconnection or loss of internet connectivities compare to previously see if the situation improve/degraded. If degrade, switch to another port and check again, if the variation from one socket to another is great, it means the source of trouble might really be your wiring.

On the site note, your "Line Attenuation" has very high values, meaning your quite far away from the DSLAM. You can call singnet to say your line is very unstable and is too far away from the DSLAM and request them to rewire to one close to your house.Hey Misato!
Guess what ? It probably is the wiring!
Here are my line stats after about a day.


Uptime: 1 day, 5:14:34
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 935 / 13.996
Data Transferred (Sent/Received) [MB/GB]: 587,90 / 1,93
Output Power (Up/Down) [dBm]: 12,5 / 1,0
Line Attenuation (Up/Down) [dB]: 8,5 / 21,0
SN Margin (Up/Down) [dB]: 7,0 / 16,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 120 / 0
FEC Errors (Up/Down): 587.202.560 / 0
CRC Errors (Up/Down): 6 / 146
HEC Errors (Up/Down): 1 / 98

This has been one of the longest time I have been connected! Thanks for your help! Much appreciated. :P

[badsector]

Uptime: 0 days, 3:47:22
Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 971 / 13.996
Data Transferred (Sent/Received) [MB/GB]: 399,65 / 1,29
Output Power (Up/Down) [dBm]: 10,0 / 7,5
Line Attenuation (Up/Down) [dB]: 7,0 / 21,0
SN Margin (Up/Down) [dB]: 7,0 / 11,5
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 620.756.992 / 0
CRC Errors (Up/Down): 3 / 5
HEC Errors (Up/Down): 0 / 2

May i know what's FEC error?
i assume my line is ok. right?

[ducklegsux]

Hi guys,

sorry as i have gotten a bit desperate for advice thus decided to post here cause simply cannot get to the helpdesk for 585i

basically my problem is that whenever i do a port forward of 10000, the router will hang and resets itself to factory defaults. other port mapping no problem ( Total of 4 port forward, non clashing), internet connectivity also no problems at all. Any advice?

firmware version on SppedTouch 585i is 6.1.4.3

[_DeeK_]

Hi guys,

sorry as i have gotten a bit desperate for advice thus decided to post here cause simply cannot get to the helpdesk for 585i

basically my problem is that whenever i do a port forward of 10000, the router will hang and resets itself to factory defaults. other port mapping no problem ( Total of 4 port forward, non clashing), internet connectivity also no problems at all. Any advice?

firmware version on SppedTouch 585i is 6.1.4.3mmm sorry dude, havent had a problem with port forwarding for the ST585i...

[chaicka]

Hi Chaicka, thanks for replying.

I am using the 5.3.8.0.0 firmware. What should i do ? Any suggestions?
5.3.8 is such an old and obsoleted firmware.....check for newer firmware, depending on which version of ST585 u have.

[sectional86]

Hi guys. I'm quite desperate. Hope u can help me here.

http://forums.vr-zone.com/showthread.php?t=179987

[Kamikazee]

Link Information


Uptime: 9 days, 22:09:48

Modulation: G.992.5 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 655 / 4.095

Data Transferred (Sent/Received) [GB/GB]: 1,11 / 6,37

Output Power (Up/Down) [dBm]: 12,5 / 1,0

Line Attenuation (Up/Down) [dB]: 9,0 / 22,0

SN Margin (Up/Down) [dB]: 17,0 / 29,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 791 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 2 / 1.355

HEC Errors (Up/Down): 0 / 646



can anyone help me analyse my line status? i have been experiencing downtime these few days.

[Ger0nim0]

Hello,

I've read trough this post for a while now and i see so many peoples with their different problems solved here...so I'm trying my luck too

I have for a couple of months a ST585v6 installed but unfortunately i'm encountering some disconnecting problems. When all the computers connected to him are online he starts to due sudden restarts in 5-30mins intervals....this is very very annoying. The ISP support said everything its ok with line and modem but obviously isn't like that. Does anyone have an advice for me regarding this issue? Thank you in advance.

Link Information

Uptime: 0 days, 1:20:48
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 509 / 4.093
Data Transferred (Sent/Received) [MB/MB]: 4,91 / 36,19
Output Power (Up/Down) [dBm]: 12,0 / 18,0
Line Attenuation (Up/Down) [dB]: 14,5 / 28,0
SN Margin (Up/Down) [dB]: 30,0 / 32,0
Vendor ID (Local/Remote): TMMB / BDCM
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 322 / 7
CRC Errors (Up/Down): 0 / 0
HEC Errors (Up/Down): 488 / 0

[chaicka]

Hello,

I've read trough this post for a while now and i see so many peoples with their different problems solved here...so I'm trying my luck too

I have for a couple of months a ST585v6 installed but unfortunately i'm encountering some disconnecting problems. When all the computers connected to him are online he starts to due sudden restarts in 5-30mins intervals....this is very very annoying. The ISP support said everything its ok with line and modem but obviously isn't like that. Does anyone have an advice for me regarding this issue? Thank you in advance.

Link Information

Uptime: 0 days, 1:20:48
Modulation: G.992.5 Annex A
Bandwidth (Up/Down) [kbps/kbps]: 509 / 4.093
Data Transferred (Sent/Received) [MB/MB]: 4,91 / 36,19
Output Power (Up/Down) [dBm]: 12,0 / 18,0
Line Attenuation (Up/Down) [dB]: 14,5 / 28,0
SN Margin (Up/Down) [dB]: 30,0 / 32,0
Vendor ID (Local/Remote): TMMB / BDCM
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 322 / 7
CRC Errors (Up/Down): 0 / 0
HEC Errors (Up/Down): 488 / 0

What's the firmware version of ur ST585v6?
What's ur plan, 1.5mbps plan?

Hmmm, looks like ur line is not on a HuaWei ADSL2+ DSLAM, or that the line card is no longer using GlobeSpan chipset.

[Ger0nim0]

What's the firmware version of ur ST585v6?
What's ur plan, 1.5mbps plan?

Hmmm, looks like ur line is not on a HuaWei ADSL2+ DSLAM, or that the line card is no longer using GlobeSpan chipset.
Ive called to the ISP and they told me that the router is v6 which means its the latest firmware installed so i don't need to install a new one...
about the my plan, it was 2.5MBps and they told me they upgraded it to 4Mbps ...still i don't know if the change to 4Mbps hes been done yet...they told me i will have it done till the end of the month


thank you for your time

[idiotekue83]

Hi guys I must say this is a great threat.. but cannot find a solution to my problem..
I've just 1-1 exchanged my ST585 for a v6, now whenever i start downloading on bitcomet, the connection to my router DC. and I have to on/off the router, wait a few minutes then can connect to internet again. this is really a problem of the router as my previous router WRT54G won't dc on bitcomet.

[idiotekue83]

ok just upgraded the firmware to 6.196 and BT does not cause dc anymore. but bt speeds become very slow <10kb/s.. i've done port forward for bitcomet, what else should i do?

[Genosidoh]

Hey guys I am currently using ST585i and my current com with Linksys Wireless G USB Adaptor to connect to my main computer with internet.

However I realise that my upload speed is capped at 4kb/sec...this causes lag for me whenever I play games. Even for frozen throne. Is there anyway i can increase the upload speed of my current com?

[noiseloops]

we've just got hold of the ST585(i) V6 yesterday for the office as we are upgrading the speed to 2.5mbps for biznet.

so far i've only managed to make it work by flashing the firmware to 5.3.8 that is provided by vrnet.

was wondering whats the newest firmware that would work with the router and also how to go about configuring this. cause i have gone through the pages in this thread, and its making me dizzy but at the same time it has been a really interesting read.

by my conclusion,
1. download the newest firmware and flash the router.
2. download the residential cd, and use it to configure it.

i tried to get hold of the vrnet dudes, but i guess most of them had left the office already, since i only called in at about 5.20pm.

hope someone could help me out here. as i wanna go in on monday prepared for some nice configs. :) thankies!

[Altec]

Anyone knows the default login and password for the ST585?

The Singtel contractor came to install MioTV but was unable to upgrade the firmware because he couldn't figure out the login ID and password. This request for ID and password only comes up when tyring to upgrade the firmware.

Tried Login as Administrator. Password was the serial no. Also tried leaving password blank. But doesn't help.

[Altec]

Anyone knows the default login and password for the ST585?

The Singtel contractor came to install MioTV but was unable to upgrade the firmware because he couldn't figure out the login ID and password. This request for ID and password only comes up when tyring to upgrade the firmware.

Tried Login as Administrator. Password was the serial no. Also tried leaving password blank. But doesn't help.

This is the screenshot from the firmware update guide.

http://i96.photobucket.com/albums/l184/ojsi/upgradeQIG.jpg

When I run update wizard, there is no IP address, version or board info displayed. Under Info, it is stated "Password protected".

[Kamikazee]

we've just got hold of the ST585(i) V6 yesterday for the office as we are upgrading the speed to 2.5mbps for biznet.

so far i've only managed to make it work by flashing the firmware to 5.3.8 that is provided by vrnet.

was wondering whats the newest firmware that would work with the router and also how to go about configuring this. cause i have gone through the pages in this thread, and its making me dizzy but at the same time it has been a really interesting read.

by my conclusion,
1. download the newest firmware and flash the router.
2. download the residential cd, and use it to configure it.

i tried to get hold of the vrnet dudes, but i guess most of them had left the office already, since i only called in at about 5.20pm.

hope someone could help me out here. as i wanna go in on monday prepared for some nice configs. :) thankies!
do u know where to download the latest firmware? how do u flash the firmware?

[Alphas]

lots of questions on 585v6, I have been running bitcomet and ppstream concurrently, no problem and very fast too. Here is my stats
Information


Product Name: ST585
Serial Number: ******
Software Release: 6.2.17.5
Configuration
Service Name: Routed PPPoE 0/100 (modified by user)
Uptime: 2 days, 1:36:01
Modulation: G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]: 651 / 3.503
Data Transferred (Sent/Received) [GB/GB]: 4,80 / 1,79
Output Power (Up/Down) [dBm]: 6,0 / 16,5
Line Attenuation (Up/Down) [dB]: 4,5 / 18,5
SN Margin (Up/Down) [dB]: 17,0 / 31,0
Vendor ID (Local/Remote): TMMB / GSPN
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 0
CRC Errors (Up/Down): 1 / 0
HEC Errors (Up/Down): 0 / 0

so far firmware 6.2.17.5 is very stable provided ur line is clean.
download the release 6.2 but dun flash yet cos its for UK ISP, need to edit the user.ini file
http://www.speedtouch.co.uk/downloads/585/62UK/585v6_62H5_UK.bin

[alvin81]

do u know where to download the latest firmware? how do u flash the firmware?

Hi, try to read the first few pages. I'm sure someone posted a site to download the firmware from.

[cuongnet]

HOT ! Fashion Shop !! iphone , nokia , samsung, motorola , sony , laptop , computer ...

[Kamikazee]

Hi, try to read the first few pages. I'm sure someone posted a site to download the firmware from.
http://mirror.opensourcehub.com/pub/speedtouch/routers/ST585v6/
ok, i just found the download link, but i got a problem now. the latest firmware for ST585v6 is v6.2.29.2 but inside the download folder only contain ZZKTAA6.2T2.bli file. how to flash it into my ST585v6? i m a networking noob, please guide me along the way.

[Altec]

Anyone knows the default login and password for the ST585?

The Singtel contractor came to install MioTV but was unable to upgrade the firmware because he couldn't figure out the login ID and password. This request for ID and password only comes up when tyring to upgrade the firmware.

Tried Login as Administrator. Password was the serial no. Also tried leaving password blank. But doesn't help.

Called Thos Solution today, distributor for the 585. They said login = Administrator, Password = serial no. If it doesn't work, need to do a hard reset.

Tried everything. Still doesn't work.......

[alvin81]

http://mirror.opensourcehub.com/pub/speedtouch/routers/ST585v6/
ok, i just found the download link, but i got a problem now. the latest firmware for ST585v6 is v6.2.29.2 but inside the download folder only contain ZZKTAA6.2T2.bli file. how to flash it into my ST585v6? i m a networking noob, please guide me along the way.

Look for the upgrade wizard program in the same ftp site.

Btw, I tried flashing to the 6.2.29.2 but failed. I think you try the 6.2.17 first.

[zhoulibin]

you may like to try this site

Upgrade utilities: http://www.speedtouchforum.de/Daten/FW/585iv6/6.2/
Firmware: http://www.speedtouchforum.de/Daten/FW/585iv6/7.4/

Note: please disable your firewall and antivirus software.
Please note: this is applicable to only the ST585i v.6


Hope that this may help.

[Kamikazee]

Called Thos Solution today, distributor for the 585. They said login = Administrator, Password = serial no. If it doesn't work, need to do a hard reset.

Tried everything. Still doesn't work.......
ok, now i have the same problem as Altec. when i try to upgrade the firmware using the wizard, it says "Password Protected". i keyed in Username: Administrator Password: serial no. but it doesn't work.

[badsector]

try leave ur password 'Blank'

[Kamikazee]

try leave ur password 'Blank'
I HAVE FOUND THE SOLUTION! thanks badsector for ur reminder! Altec, after u key in the word "Administrator" in the username box, STRAIGHT AWAY PRESS ENTER from there, leave the password alone. hope it works for u. :D

[alvin81]

you may like to try this site

Upgrade utilities: http://www.speedtouchforum.de/Daten/FW/585iv6/6.2/
Firmware: http://www.speedtouchforum.de/Daten/FW/585iv6/7.4/

Note: please disable your firewall and antivirus software.
Please note: this is applicable to only the ST585i v.6


Hope that this may help.

I don't think the SG model is 585iv6...

[alvin81]

I can't seems to flash my firmware to 6.2.29.0. The upgrade wizard kept on reporting that the device failed to respond during discovery. Anyone got any idea why? :s11:

[Kamikazee]

I can't seems to flash my firmware to 6.2.29.0. The upgrade wizard kept on reporting that the device failed to respond during discovery. Anyone got any idea why? :s11:
yeah, i have this problem too. even when i flash other firmware version, when its going to complete, it keep reporting that the device failed to respond during discovery. but when i restart my ST585, the firmware is upgraded. weird.....

[Altec]

I HAVE FOUND THE SOLUTION! thanks badsector for ur reminder! Altec, after u key in the word "Administrator" in the username box, STRAIGHT AWAY PRESS ENTER from there, leave the password alone. hope it works for u. :D

Tried it. But still doesn't work for me. :(
Looks like the only option is to bring my modem down to Thos Solutions at Science Park Drive to see what they can do.

[chaicka]

I don't think the SG model is 585iv6...
There are both ST585 and ST585v6 bundled with SingNet plans...depending on when u sign up.

[Kamikazee]

throughout the whole firmwares avaliable for ST585v6, which version is the best and most stable?

[Altec]

Tried it. But still doesn't work for me. :(
Looks like the only option is to bring my modem down to Thos Solutions at Science Park Drive to see what they can do.

Thos Solution was very helpful. Confirmed that ST585 v5 definitely cannot upgrade firmware. So cannot use with MioTV.

Only ST585v6 firmware can be upgraded.

[AttentioN]

Thos Solution was very helpful. Confirmed that ST585 v5 definitely cannot upgrade firmware. So cannot use with MioTV.

Only ST585v6 firmware can be upgraded.

Argh. i was about to get ST585 from a user until i confirmed with him, it was v5. Which didnt support miotv. :(

I wonder where can i purchase ST585v6 in Sg?

[liangtam]

Actually, it does not really matter. So long as the modem accepts multiple PPPoE connection. But if you really wan to be on safe side, then keep sourcing for a v6 bah.

[Altec]

Actually, it does not really matter. So long as the modem accepts multiple PPPoE connection. But if you really wan to be on safe side, then keep sourcing for a v6 bah.

Actually it does matter. Spent about 2 weeks searching for a solution to upgrade the firmware to IPTV for the ST585 v5. Singnet MioTV contractor also spent 2 hours trying to find a solution. Finally, THos Solution confirmed that it can't be done.

Anyone successfully upgraded the firmware of the ST585 v5?

[Altec]

Argh. i was about to get ST585 from a user until i confirmed with him, it was v5. Which didnt support miotv. :(

I wonder where can i purchase ST585v6 in Sg?

You can purchase from Thos Solution. The sign at their shop stated $128. But better call to confirm first. If you do not need wi-fi, or have your own wi-fi router, you can consider the ST536v6 for $88.

Thos Solution
73 Science Park Drive
#02-06
Cintech 1 Building
Tel: 67739693

Opening hours:
M - F: 9 am - 6 pm
S: 9 am - 12 pm.

[AttentioN]

So i guess the st585v6 supports IPTV whereas the v5 doesnt?

Actually, i already have ST536v6. now im looking for other solutions.

[Altec]

So i guess the st585v6 supports IPTV whereas the v5 doesnt?

Actually, i already have ST536v6. now im looking for other solutions.

On its own, the St585 v6 does not support IPTV. But the firmware can be updated to support IPTV.

The MioTV contractor would have the firmware. But sometimes they forget to bring the CD when they come down to do the set up. The last time the MioTV contractor came, he had to call his friend to bring it for him.

[AttentioN]

I see..ok, ive just gotten my hands on ST585v5. Will try2 out a little with it. :D

[Altec]

I see..ok, ive just gotten my hands on ST585v5. Will try2 out a little with it. :D

Let us know if you managed to flash the firmware.

[sectional86]

Hi everyone. Would like to ask if any of you have manage to set up FTP using a NAS like DNS-323 successfully over the ST585? I couldnt get ST585 to connect to the DNS-323 thouigh i've forwarded the ports, DDNS it and use the "always use the same IP address", not static IP. I keep going into the FTP server for the ST585.

[qinglong]

i tried setting up iptv on st585 v6.
got to the point where i can view the channels, but the streaming stops after about 10s.
if i change channel, it streams again but for 10s also.

seems like i got the connection, but what's causing it to stall.
anyone actually got the st585 v6 working with iptv?

[AttentioN]

Let us know if you managed to flash the firmware.

i cant even get hold of the firmware which supports iptv.

[sectional86]

Hi everyone. Would like to ask if any of you have manage to set up FTP using a NAS like DNS-323 successfully over the ST585? I couldnt get ST585 to connect to the DNS-323 thouigh i've forwarded the ports, DDNS it and use the "always use the same IP address", not static IP. I keep going into the FTP server for the ST585.
anyone can help?

[lvlaTr1X]

anyone can help?

same problem here... anyone?

[Kamikazee]

how to change modemoption via editing config file? i can't find any steps listed here.

[dekkei86]

how to change modemoption via editing config file? i can't find any steps listed here.
1) Open a web browser like Internet Explorer or Firefox and type http://192.168.1.254/ to login into SpeedTouch configuration page.
2) Click "SpeedTouch" on the left side of the page.
3) Click "Configuration" link on the main page.
4) At the bottom of the page, click "Save or Restore Configuration" link.
5) At Backup & Restore page, under Backup current configuration, click the "Backup Configuration Now..." button, it will prompt you to save the user.ini file. Save the user.ini file onto Desktop.
6) Open the user.ini file, search and modify the config file's statement: modemoption=00:06:03:01:00:.....
7) Save the updated user.ini file.
8) Go back to the Backup & Restore page, under Restore saved configuration, upload the updated user.ini file and click "Restore Configuration Now..." button.



You are done! Hope this can help you!
:D :D :D

[coppermine]

sorry for the dig.

anyone manage to get the mrtg on the 5.4 firmware? I only manage to get mrtg working on 5.3.8.1.0 firmware. read that 5.4 snmp is broken, need to double confirm.

[RurouniX]

I'm experiencing a little technical difficulty... I am unable to access my 585's configuration page. Anyone knows what's the problem?

[mok]

I'm experiencing a little technical difficulty... I am unable to access my 585's configuration page. Anyone knows what's the problem?

Have you tried connecting directly to the router with a LAN cable and access the configuration page?

[RurouniX]

Have you tried connecting directly to the router with a LAN cable and access the configuration page?

I'm already connected to my router via lan cable.

[mok]

Please specify the steps and address you input in your attempt, as well as the error message encountered.

[RurouniX]

I tried to enter the configuration page by typing in the address (192.168.1.254), and after a long time of loading, I got this:

Internet Explorer cannot display the webpage

Most likely causes:
You are not connected to the Internet.
The website is encountering problems.
There might be a typing error in the address.

What you can try:
Diagnose Connection Problems

More information

[elu]

I tried to enter the configuration page by typing in the address (192.168.1.254), and after a long time of loading, I got this:

Internet Explorer cannot display the webpage

Most likely causes:
You are not connected to the Internet.
The website is encountering problems.
There might be a typing error in the address.

What you can try:
Diagnose Connection Problems

More information



Disabled proxy?

[badsector]

ur firewall blocking it?

[RurouniX]

I'm not using a proxy...

ur firewall blocking it?

Can the router's firewall do that?

[badsector]

i mean software firewall. e.g windows firewall..
can u ping it?
since u still able to use it but cant access config page. most likely problem not from the modem/router.
i'm still suspecting it's your proxy setting. if u can ping it

[RurouniX]

i mean software firewall. e.g windows firewall..
can u ping it?
since u still able to use it but cant access config page. most likely problem not from the modem/router.
i'm still suspecting it's your proxy setting. if u can ping it

Just tried pinging it.. and I got a stable response.

[_DeeK_]

I recently changed some settings with the Residential CD and my DSL line just went bonkers.

This is my line stats,

DSL Connection

Link Information

Link Status: Disconnected
DSL Type: UNKNOWN

Any help here ? I cant even seem to get the modem connected to the DSL line. The phone dial tone is perfectly fine :(

[chaicka]

I recently changed some settings with the Residential CD and my DSL line just went bonkers.

This is my line stats,

DSL Connection

Link Information

Link Status: Disconnected
DSL Type: UNKNOWN

Any help here ? I cant even seem to get the modem connected to the DSL line. The phone dial tone is perfectly fine :(
Check the modemoptions=xxxxxxxxxxxx in the configuration.
Else reset and reconfigure from fresh using the Setup Wizard in the CPE itself.

Not sure what you changed, so hard to advice what to do.

[_DeeK_]

Check the modemoptions=xxxxxxxxxxxx in the configuration.
Else reset and reconfigure from fresh using the Setup Wizard in the CPE itself.

Not sure what you changed, so hard to advice what to do.

Hi chaicka,

Thanks for the prompt reply.

I went to change the service to EthoA&DHCP with NAT. Me and my itchy fingers :s27:

Hence after that, all DSL connection just seemed to halt. Cant even get to connect to it.

[_DeeK_]

Did so many checks and found out that the DSL link is totally down.

The modem cant even detect the DSL Connection.

Link Status : Disconnected

Any work around ?

I arranged for the SNBB Technician to come down already :(

[chaicka]

Did so many checks and found out that the DSL link is totally down.

The modem cant even detect the DSL Connection.

Link Status : Disconnected

Any work around ?

I arranged for the SNBB Technician to come down already :(

SingNet's connection is not EthoA. It should be PPPoE or PPPoA. PPPoA is better but not necessary works for all line connections.

[_DeeK_]

SingNet's connection is not EthoA. It should be PPPoE or PPPoA. PPPoA is better but not necessary works for all line connections.

Yea i know. My old config used to be PPPoA.

Its just that after i configured to EthoA (itchy hands), I cant even detect the DSL line! Any suggestions ?

Anyway, the technician is coming down today. Hope its resolved :s13:

[RurouniX]

Does anyone know what's a good firmware for the 585 v6?

[badsector]

update the latest v7.432... mins ago.... cant tell the diff yet

[yuyyder]

hi, my st585v6 came with my singnet bb contract about 2 years ago. the wired connection is working fine. but the wireless connection i could never get it to work. it was working for a while very long ago. i cant even find its SSID when it is broadcasting.

Can anyone help ? Because I want to get online with the nintendo DS.. and I cant do anything now. Is it possible the wireless part is spoiled ?

[albertchng]

hi, my st585v6 came with my singnet bb contract about 2 years ago. the wired connection is working fine. but the wireless connection i could never get it to work. it was working for a while very long ago. i cant even find its SSID when it is broadcasting.

Can anyone help ? Because I want to get online with the nintendo DS.. and I cant do anything now. Is it possible the wireless part is spoiled ?


Cant you open a new thread?

This thread is so old & long, you still hijack it to post your problem... did you look through all 115 pages, i'm sure your answer is in there.

[_DeeK_]

I may be wrong, but u may wanna take a look at how to forward GRE protocol. Take note, those ports u open up are TCP ports, not the GRE protocol.

Sorry to dig up a old reponse but anyone knows how to configure the CLI to allow forwarding GRE protocol.

I have read the CLI guide and tried configuring but still, It seems that there is something that I am not doing right.

Anyone ? Will post up my firmware version when I get back lol

[Webbyboy]

Im using the older version of ST585 and recently just upgrade from 3mbps -> 8mbps:

I've been experiencing disconnects and couldn't authenticate after a while. This is my DSL link status:

Link Information


Uptime: 0 days, 0:10:32

Modulation: G.992.5 Annex A

Bandwidth (Up/Down) [kbps/kbps]: 950 / 13.650

Data Transferred (Sent/Received) [MB/MB]: 9,17 / 49,91

Output Power (Up/Down) [dBm]: 12,5 / 1,5

Line Attenuation (Up/Down) [dB]: 8,5 / 21,0

SN Margin (Up/Down) [dB]: 7,5 / 10,5

Vendor ID (Local/Remote): TMMB / GSPN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 20 / 0

FEC Errors (Up/Down): 4 / 1.142.085

CRC Errors (Up/Down): 3 / 4.449

HEC Errors (Up/Down): 7 / 84



Im getting very bad CRC/FEC/HEC errors..what could be the problem?

[liangtam]

did u flash it to another firmware that is not SingTel customised?

[Webbyboy]

did u flash it to another firmware that is not SingTel customised?

Yes on generic firmware:

Software Release: 5.4.0.14
Software Variant: AA
Boot Loader Version: 1.0.16


Current updates:

FEC Errors (Up/Down): 16 / 53.531.573
CRC Errors (Up/Down): 3 / 6.866
HEC Errors (Up/Down): 7 / 496

[liangtam]

fixed back the modemoption field?

[Webbyboy]

fixed back the modemoption field?

the modemoption has been always intact.

[leader288]

I've been having problems with my ST585(i) v6. I cannot log into MSN using Adium unless i check the "connect via http" box. Can anyone help?

[badsector]

I've been having problems with my ST585(i) v6. I cannot log into MSN using Adium unless i check the "connect via http" box. Can anyone help?

u sure it's st585's issue. not Adium?

[leader288]

u sure it's st585's issue. not Adium?
yep. my friends came over and tried to use adium. needless to say it failed too. I've already enabled port forwading using the preset MSN on the http GUI but my brother's msn LIVE is also having problems.

[badsector]

nv try adium before. but i'm using MSN with any port forward/firewall disabled. using firmware 7.4.3.2
you just start using adium or only test recently?

[yeng9ph]

hi all... anyone can help regarding this same problem? mine is i am connecting to a DHCP server and i think this sppedtouch is PPPoE type.. how to deal with this..thanks..

[Kamikazee]

any latest updates on firmware for speedtouch 585?

[sunseer]

Hi guys,

Would like to know if my link status are ok. thanks!

http://i686.photobucket.com/albums/vv227/sunseer/DSLStatus330.jpg

ops. I am on a 3Mbps plan. ^^;

[liangtam]

You nvr write plan how to know?

[sunseer]

Hi guys,

Would like to know if my link status are ok. thanks!

http://i686.photobucket.com/albums/vv227/sunseer/DSLStatus330.jpg

ops. I am on a 3Mbps plan. ^^;

any comment on the link status??