[miyamew]

wahkao3 wrote:

the contractor's workers clean one mah, not i clean

u sure after that u dont have to vacuum/sweep and mop the floor

its a big headache.... and move the stuffs back to its original place...

most contractor workers will keep their tools and ask u sign the invoice n go off....

dont think they so free to clean for u... maybe only those big debris which is too obvious lah.....

unless u dont do drilling (if u already install before) then there's nothing much to clean up lor

[lifesgood]

wahkao3 wrote:

2.8k for inverter sys 3
include new trunking and piping

thanks for sharing
thats a gd deal man.. where u get that offer?

[wahkao3]

[GPGT] My Mitsubishi inverter system 3 air con arrived today!!

GPGT

[wahkao3]

[wahkao3]

[b3n]

Hi guys
Hv decided either Mitsubishi or Panasonic system 3 inverter. Not sure if I can hv it installed as my HDB bedrm has 66omm ht opening? Pls can anyone advise? (I kana con to buy LG & stand to lose 250 deposit)

[Laneige]

for those with long living room n dining room, what is the BTU of yr aircon unit?

how much will a mitsubishi sys 2 (1x 24000??? BTU, 9000) costed? thanks

oh did any of u guys hide the piping in the false ceiling or L box?

[cartoon2211]

b3n wrote:

Hi guys
Hv decided either Mitsubishi or Panasonic system 3 inverter. Not sure if I can hv it installed as my HDB bedrm has 66omm ht opening? Pls can anyone advise? (I kana con to buy LG & stand to lose 250 deposit)

I got my Pana sys 3 inventer recently... I'm having a push-out window type for my masterbed room, after installing the new bracket, the installer then realised that they may have to "file" the lower part of the window! And told me there's no way to lower the bracket further (which I doubt so). But luckily after installing the condenser, my window was able to open without any "filing"... it misses the condenser by merely a 3mm gap!

So far I'm happy with this product, it's quiet and able to cool my room fast (compare to my previous non-inverter unit).

[tazzycorner]

i am planning to install air-cons in 4 bedrooms ...
thinking of getting two sets of systems 2 ... roughly how much would it cost?

any recommendations or advice will be much appreciated.

thanks in advance!

[Innocast]

cartoon2211 wrote:

I got my Pana sys 3 inventer recently... I'm having a push-out window type for my masterbed room, after installing the new bracket, the installer then realised that they may have to "file" the lower part of the window! And told me there's no way to lower the bracket further (which I doubt so). But luckily after installing the condenser, my window was able to open without any "filing"... it misses the condenser by merely a 3mm gap!

So far I'm happy with this product, it's quiet and able to cool my room fast (compare to my previous non-inverter unit).

inverter ish good, especially the electricity bill raised like hell........in long run it is more cost savings to spend a little more to buy inverter aircon at the initial installation stage....

[wahkao3]

b3n wrote:

Hi guys
Hv decided either Mitsubishi or Panasonic system 3 inverter. Not sure if I can hv it installed as my HDB bedrm has 66omm ht opening? Pls can anyone advise? (I kana con to buy LG & stand to lose 250 deposit)

660mm is not enough, u need 800mm
make sure your contractor is prepared to install it for u by pushing it from another window ledge

i suggest you ditch panasonic like i did. Initially i still wanted panasonic but if the compressor need to change under warrenty or anything, other contractors might not be willing to push it through the other window ledge

[cannotliao]

http://www.mr-mckenic.com/

http://www.airconcare.com/

saw these at HomeFix. anyone use them before? how the performance?
any DiY tips to share for removing sourish and musty smell from the aircon FCU?





anyone even use this dettol spray into the FCU? will cause damage the aircon or not?

[sentosaubin]

Dear aircon expert..

I'm contemplating of changing my aircon to system 3.
My floor plan is below.
From the discussion that I read, I guess 9000 BTU for each room will be sufficient. Note that I plan to extend my aircon to the "Utility Room" behind the kitchen as well.
Is it feasible? Is there any optimised place to put the FCU?

Another question.. since at the right side of BR is a staircase, do you think I can put the Outdoor Compressor unit there?

[chunlianghere]

sentosaubin wrote:

Dear aircon expert..

I'm contemplating of changing my aircon to system 3.
My floor plan is below.
From the discussion that I read, I guess 9000 BTU for each room will be sufficient. Note that I plan to extend my aircon to the "Utility Room" behind the kitchen as well.
Is it feasible? Is there any optimised place to put the FCU?

Another question.. since at the right side of BR is a staircase, do you think I can put the Outdoor Compressor unit there?

is the utility room added during MUP(main upgrading programme)?

if it is so, than the condenser cannot be placed at utility room.

it will be placed outside master bedroom wit bracket.

yes, u can install fcu at utility room. jus tat will drill many holes to go through 2 toilets.

[sentosaubin]

chunlianghere wrote:

is the utility room added during MUP(main upgrading programme)?

if it is so, than the condenser cannot be placed at utility room.

it will be placed outside master bedroom wit bracket.

yes, u can install fcu at utility room. jus tat will drill many holes to go through 2 toilets.

You are right, the utility room is added during MUP

I don't plan to put condensor inside utility room. I plan to either put it outside Master BR or at the right side of master BR, which is a staircase

go through toilets huh.... i would rather it go through the wall in the kitchen?