[kimsim]

Boeing101 wrote:

If i buy aircon, you think 2 tick better or 4 tick?
I know 4 tick save energy, but what is the disadvantage?

From my fringe experience, i will never buy more tick fridge anymore, the compartment not cold one. The ice i took out from more tick one melt much much faster than less tick one.

I think the tick is as bad idea as like our water saving device install at tap outlet. Its a piece of bad idea from someone on top.

So far 4ticks only, Daikin 20k btu sys 3, MHI sys 2 and LG artcool only.
But 5 ticks ME starmex coming soon..

For my experience, has more ticks meant can be reaching faster cooling capacity and cut-off during outdoor compressor time is a greater.

IF has more ticks but slower temperature pre-set are achieved in slower than 2 ticks, actually to be an equal also.

Usually more powerful needs draw more power input watts for shorten time than slower but use lesser input watts = energy saving.

At the end 4-5 ticks user still prefer to set few more stop lower temp. degree than 2 ticks energy saving model as well.

[cookieemonsterr]

I previously did my aircon for 3.6k panasonic sys 4 (18k plus 3x9k). Got200 dollar ntuc vouchers also. From Aktiff engrg

I need air con for my mums flat again, anyone has any recommendations? If not ill probably go back to the same company. Looking for mitsu sys 4 inverter. Has to use good thicker pipes and excellent worksmanship. Saw creations on fb but they have atrocious reviews.

Thanks

[smurf75]

Hi , can anyone advise ?

Coming resale 5room flat 36years old, intend to install ME system4.
Will be partition out a room from living room so will be 4 bedrooms total.

MBR = 12k btu
3BR = 9K btu

Most likely will be on all the unit every night , will the MXY4A38 be enough or the new model MXY4G38 be better?

Thank in advance.

[qiuqiuxy]

Anyone can advise how to choose between ME Starmex MSYGE10VA vs MSYGE13VA?

[kimsim]

qiuqiuxy wrote:

Anyone can advise how to choose between ME Starmex MSYGE10VA vs MSYGE13VA?

Depend your room size..
3x4m = 10k
3.5x5m = 13k

[kimsim]

smurf75 wrote:

Hi , can anyone advise ?

Coming resale 5room flat 36years old, intend to install ME system4.
Will be partition out a room from living room so will be 4 bedrooms total.

MBR = 12k btu
3BR = 9K btu

Most likely will be on all the unit every night , will the MXY4A38 be enough or the new model MXY4G38 be better?

Thank in advance.

MXY4G38 all new design and outdoor slightly shorten, more easier to loading out from window.

[smurf75]

Thx for the advise , will the mxy4g38 limit to the 8.5A as HDB rule?

[tlkchew]

Hi Anyone can advice which Aircon is good for 5rm HDB.

I am changing out old aircon. 2x 9000 (Bd room) 1x 12000 (MBdroom) and 1x9000+1x12000 (living room) (fujitsu 5 in 1)

Thinking of 9000 BTU x 3 for room , what do your guys suggest for living room.? sshould i look for 2 x9000 or go with 1x18000

this is for standard HDB 5rm 110m2 in Sengkang.

thanks in adv

[hOp3SoT]

hey guys, can check wat is the issue if all 3 Mitsubishi units has continuous blink on the top light indicator after they were on for while and no air is blowing out? (after a power surge) thx!

[kwaychapy]

thinking of installing 1 x 18000 btu unit for living room.. nid another compressor + trunking etc.. any bros have had experience in adding on air con? i oredi have 3 units installed fornthe bedrooms..

[STREAM2]

hOp3SoT wrote:

hey guys, can check wat is the issue if all 3 Mitsubishi units has continuous blink on the top light indicator after they were on for while and no air is blowing out? (after a power surge) thx!

Check the number of blinks and refer to this site :
http://www.astiquer.com/aircon-blink...ion-codes.html

[hOp3SoT]

its seems like its just constant blinking wif no interval/pause.

[Hellooo]

Anyone install their air-con by harvest aire pte ltd? Any review?

[kimsim]

hOp3SoT wrote:

hey guys, can check wat is the issue if all 3 Mitsubishi units has continuous blink on the top light indicator after they were on for while and no air is blowing out? (after a power surge) thx!

Fan motor kaput, or PCB faulty, what is the model?

[hOp3SoT]

kimsim wrote:

Fan motor kaput, or PCB faulty, what is the model?

its Starmex MXY3A28VA. just installed for 1mth + only.