[Vampire05]

one more question, after I changed the singtel ONR to bridge mode, can the 4 ports behind the ONR still be used like before?

[giraffey]

Vampire05 wrote:

one more question, after I changed the singtel ONR to bridge mode, can the 4 ports behind the ONR still be used like before?

No. Only 1 port.

[Vampire05]

so that means if I am on singnet 2gbps plan, it is not advisable to make my ONR to bridge mode because I will only get a 1gbps speed?

[giraffey]

Vampire05 wrote:

so that means if I am on singnet 2gbps plan, it is not advisable to make my ONR to bridge mode because I will only get a 1gbps speed?

Yes, you are right. Same for other 2Gbps plans on the other ISPs.(for some ISPs, they allow a single 2gbps (single port) connectivity as well, but it would mean having to buy routers and network cards supporting higher speeds)

[kartz4u]

Hi

Anyone aware of the username and password for Singtel ONR HG8240T5? Appreciate the help.

Many thanks

[kajdex]

kartz4u wrote:

Hi

Anyone aware of the username and password for Singtel ONR HG8240T5? Appreciate the help.

Many thanks

Have you tried
username: support
password: last 10 characters of the ONR's Serial but on reverse e.g. if Router Serial is 1234567890ABCDEF then the password is FEDCBA0987

[ah_pok]

Hi All,

I'm currently using Whizcomms and they issue a HG8240T5 to me.

I manage to login using Support account.

After that i did this:

(HG8240T5)
1. Turn on DHCP Relay
2. Change to Bridge mode.

(TP-Link Archer C9)
3. Under IPTV, i added VLAN 10 as internet connection.

But somehow my router just unable to get the Public IP.

Any pro here can help?

Many thanks!!

[uncle_josh]

1. Whizcomms no IPTV
2. Whizcomms no VLAN
3. Bridge WILL NOt GET ANY IP ADDRESS.

[bvtter]

cnet wrote:

Hi,

I have the Software version: V3R017C00S100.
Managed to set to bridge mode.
Connected to AX88U (router mode) is ok for internet.
But when set the IPTV for MIO TV connection, the internet connection is cut off. When disable IPTV, Internet connection back again.
Even run the setup wizard, please choose "special requirement from ISP process but still failed.
Trying all the LAN port combination but still failed.
Anyone has any experience to fix on this

Hi did you manage to solve this?

[bvtter]

kero89 wrote:

Thanks to TS for this well written guide! Just managed to do mine and all is well. Except...

1) I didn't need to set preset on my asus.
2) the Internet led doesn't light up on my ONR

And how do i access the ONR web gui if I need to one day? Tried to connect direct but still can't reach the gui. Hmm

Did you manage to get back into the webui?

[mun_hoe]

ah_pok wrote:

Hi All,

I'm currently using Whizcomms and they issue a HG8240T5 to me.

I manage to login using Support account.

After that i did this:

(HG8240T5)
1. Turn on DHCP Relay
2. Change to Bridge mode.

(TP-Link Archer C9)
3. Under IPTV, i added VLAN 10 as internet connection.

But somehow my router just unable to get the Public IP.

Any pro here can help?

Many thanks!!

if ONT is set to bridge mode. need not tag VLAN on router end.

[kero89]

bvtter wrote:

Did you manage to get back into the webui?

No. Lol there’s no hard reset on this onr as well. But from march until now all good. Fingers crossed.

But i searched this online.

Reset Huawei HG8244H Ooredoo router to factory defaults
To reset the Huawei HG8244H Ooredoo to its default settings, you have to do the following steps:
Turn on router
Press Factory Reset button and hold for at least 15 seconds
Device restarts automatically
Default settings have been restored

I wonder where is the sacred button.

[tuntun]

I just subscribed to Singtel and scheduled to install on 24 June. Can I request installer tech to configure ONR port 1 to get public IP and 2-4 configure to use with TV service?
I have given a router from office IS dept with preconfigured of VPN to HQ. But it needs a public IP to connect at WAN port. Double NAT cannot access. Is ti possible or anyone can advise/help me after singtel installation?
Thanks

[xiaofan]

tuntun wrote:

I just subscribed to Singtel and scheduled to install on 24 June. Can I request installer tech to configure ONR port 1 to get public IP and 2-4 configure to use with TV service?
I have given a router from office IS dept with preconfigured of VPN to HQ. But it needs a public IP to connect at WAN port. Double NAT cannot access. Is ti possible or anyone can advise/help me after singtel installation?
Thanks

You can always try to ask SingTel help before the installation. Do you have SingTel TV services? How many boxes? Chances are not high though.

Since you have legitimate use cases for work, the easier way is to convince your company to pay you a separate line (say M1 500Mbps plan for S$29.9 per month) and then use it for your work.

If you do it post installation to configure as a single port ONT, you need to check if your company issued router supports vlan or not. Moreover, even if it does, it is not supported by SingTel and you are on your own.

[uncle_josh]

firstly Singtel only issues ONR to new subscribers. too bad you did not do your home work.

to use your own router you need to go to M1/SH/MR/WC

option 1
bang table ask to bridge the ONR

option 2 change to 1 + 1Gbps
where they will let you use one of the port with WAN ip address to use with 3rd party routers

option 3
change/subscribe to a new isp

Sent from 天作孽 犹可恕 自作孽 不可活 using GAGT