Moving RAID 1 HDD to my PC

Gymrat76

Supremacy Member
Joined
May 8, 2003
Messages
7,851
Reaction score
80
Hi all

A bit of a strange question. I had a drive on my RAID array that degraded, so I replaced both drives and wanted to move the working HDD from my NAS to an internal drive bay on my PC.

The drive can be seen in BIOS, but when I boot up Windows, it doesn't show up in Explorer. I can see it in Disk Management, but I don't otherwise know how to access data off that disk. I assumed I could just access like any normal drive, but it seems its not the case. What can I do to access data from the old NAS RAID 1 drive?
 

Gymrat76

Supremacy Member
Joined
May 8, 2003
Messages
7,851
Reaction score
80
One additional piece of information. On Disk Management, the system column is blank. My other internal drives show NTFS...
 

commach

Great Supremacy Member
Joined
Apr 11, 2001
Messages
53,997
Reaction score
18
The RAID1 array likely not using NTFS, most probably using proprietary file system not directly accessible using Windows.

Find out what kind of file system for the NAS RAID1 array, without any information of the NAS, we can't provide constructive advice for your problem.
 

MoneyFace =p

High Supremacy Member
Joined
Dec 17, 2010
Messages
35,380
Reaction score
402
Hi all

A bit of a strange question. I had a drive on my RAID array that degraded, so I replaced both drives and wanted to move the working HDD from my NAS to an internal drive bay on my PC.

The drive can be seen in BIOS, but when I boot up Windows, it doesn't show up in Explorer. I can see it in Disk Management, but I don't otherwise know how to access data off that disk. I assumed I could just access like any normal drive, but it seems its not the case. What can I do to access data from the old NAS RAID 1 drive?

A picture speaks a thousand words. It will really be much more helpful with that.

No drive letter allocated to the partition in that drive? Tried assigning one for it?
 

Gymrat76

Supremacy Member
Joined
May 8, 2003
Messages
7,851
Reaction score
80
Hi,

The NAS is the D-Link DNS-320, with 2.05 firmware.

I tried putting both old HDDs (one after another) with one of the new HDDs into the NAS, hoping it would rebuild to the new HDD, but it kept saying it was degraded (both my old drives) and asked me to reformat.

In the end, I've put both old drives back into the NAS, remapped the drive and am now copying the contents to an internal HDD. I will then pop in the new HDDs and copy everything over. Time consuming, but the only way I could think of to get my data.

I hour and 150+GB to go...
 

jtjt00

Arch-Supremacy Member
Joined
Jan 1, 2000
Messages
17,741
Reaction score
556
Suspect both old HDDs are having problem.
Once copy out all data, connect to desktop and use HDTune to scan for error. Do not check Quick scan.
 

Gymrat76

Supremacy Member
Joined
May 8, 2003
Messages
7,851
Reaction score
80
Update:

I now think that perhaps my NAS is the issue.

I had earlier set RAID 1 and did a reformat of the 2 brand new WD Green HDDs before swapping my old HDD back into the NAS to copy out the files. Now, when I pop the 2 new HDDs back into the NAS and go into the Disk Management, it tells me the RAID 1 is degraded. S.M.A.R.T check of both drives show no problems. :vijayadmin:
 
Important Forum Advisory Note
This forum is moderated by volunteer moderators who will react only to members' feedback on posts. Moderators are not employees or representatives of HWZ Forums. Forum members and moderators are responsible for their own posts. Please refer to our Community Guidelines and Standards and Terms and Conditions for more information.
Top