Help needed !

[JY1199]

Hello everyone. I have an issue with my newly build rig. Just assemble last week. I'm using a lian li dynamic evo in reverse build. My gpu isn't vertical just the normal horizontal way. My issue is the top lian li fans (just above the gpu) I notice is currently melting/bending at the small side of the fans case. the little triangle corner to be more specific. Is it due to the heat from the gpu ? I should mention my aio is also situated at the top not the side. If I'm not wrong the top fans are set to exhaust. Sorry I'm not that good with IT stuffs. Any help would be appreciated!

 

[JY1199]

You will need the Lian Li GEN 4.0 PCIE RISER CABLE. It look nicer and not weird to me. Sorry to say that the GPU upside down look more weird to me.

Very nice. i think i'll change it to upright. Does sim lim sell the riser cable ? i see most sell not the 600mm one.

 

[KleoZy]

Yea i should have went with upright build. But would'nt it be a bit hard plugging the cables all the way to the front ? It's kinda weird too.

what burn or melt are you concern? I don't see any burns or melt, even after downloading your pics and zoom it. it looks perfectly fine to me...

 

[celsus]

Is it the fans vibration pads in the corners slightly peeling? It is only stuck on with glue. Use finger press back?

 

[JY1199]

what burn or melt are you concern? I don't see any burns or melt, even after downloading your pics and zoom it. it looks perfectly fine to me...

I didn't mention burn. More like due to heat bending. I'll upload my pic again but i'll circle the problem i'm trying to mention.

 

[tang_tang]

Very nice. i think i'll change it to upright. Does sim lim sell the riser cable ? i see most sell not the 600mm one.

Your builder should be able to do it for you.

https://shopee.sg/Lian-Li-O11-Dynam...1DE-2X-White-O11DE-2W--i.27976951.14126150922

 

[JY1199]

Is it the fans vibration pads in the corners slightly peeling? It is only stuck on with glue. Use finger press back?

Yea its at the corner of the fan case. The small triangle which is holding the screw. Will try pushing it back once i'm home.

 

[JY1199]

Just bought 2 days only. Then it became like this. It can't be normal right ?

 

[KleoZy]

Just bought 2 days only. Then it became like this. It can't be normal right ?

ok, is either you faster go back to the shop who fix this PC for you.. if not they will ask you to RMA the fans yourself. your SL120 infinity peels off. it should not be this way.. infact I ryou might consider AL

 

[Koenig168]

That's the anti-vibration pads peeling off. Just press against the fan and add some glue if necessary.

 

[celsus]

Its not normal but lets say quite common and nothing to worry about. Remove is totally fine also, I took them off on my build. They are there to dampen vibration sound if screws loosen. Better just tighten it if you hear such sounds

 

[KleoZy]

Just bought 2 days only. Then it became like this. It can't be normal right ?

btw. these are caused by using electrical screwdriver. if use manual screwdriver will not be this way.

 

[JY1199]

ok, is either you faster go back to the shop who fix this PC for you.. if not they will ask you to RMA the fans yourself. your SL120 infinity peels off. it should not be this way.. infact I ryou might consider AL

Yes i just contacted dynacore and they said this isn't normal. So i'll bring it down. Noted on the screwdriver. Thank you for helping me out !

 

[JY1199]

That's the anti-vibration pads peeling off. Just press against the fan and add some glue if necessary.

Noted. Will try pressing it back. Thanks !

 

[JY1199]

Its not normal but lets say quite common and nothing to worry about. Remove is totally fine also, I took them off on my build. They are there to dampen vibration sound if screws loosen. Better just tighten it if you hear such sounds

I see. Hopefully its nothing major. Also i realize my com idling is at 47 degree. I believe that's not normal. But thanks for the inputs !