help! pc cant power on after remove gpu

[BUBUBU]

i power off my pc unplug power cable

then i remove the gpu which is gtx960

after that i power on my pc , nothing happen

so i take out the power cable , and insert back the graphic card to the slot and insert back the pci cables


power on pc again , nothing happen


how to fix?

 

[herman1314]

did you insert the video cable at the motherboard instead of the graphics card?

 

[BUBUBU]

did you insert the video cable at the motherboard instead of the graphics card?

mean? i already mention wat i did

after i take out the gpu , i just power on again , nvr touch any cable

 

[ykgoh]

So is your PSU fan spinning?
Your casing fans spinning?
Your CPU cooler fan spinning?
If your mobo has status LED, is it lit?
If you have PC speaker connected, any beeps?

Quite common for slight movement when pulling out your GPU to cause loose connection.

Make sure all your cables are plugged back tight.

 

[Phen8210]

Your PSU switch is on?
Re-plug in your power cable, make sure it goes all the way in.

Btw, you should always switch off the psu before plugging out the power cable

 

[BUBUBU]

So is your PSU fan spinning?
Your casing fans spinning?
Your CPU cooler fan spinning?
If your mobo has status LED, is it lit?
If you have PC speaker connected, any beeps?

Quite common for slight movement when pulling out your GPU to cause loose connection.

Make sure all your cables are plugged back tight.

psu fan is?

nothing is spinning except the mobo led is turn on
no beep from speaker either

i only touch the power cable and gpu cable

all is tight also cant

 

[BUBUBU]

Your PSU switch is on?
Re-plug in your power cable, make sure it goes all the way in.

Btw, you should always switch off the psu before plugging out the power cable

ya on

dam i nvr switch off psu before plugging out

so how?

if i bring to pc shop how much it cost to fix?

 

[jtjt00]

ya on

dam i nvr switch off psu before plugging out

so how?

if i bring to pc shop how much it cost to fix?

You unplug while the mains is still on? Like that, you need to bring rig to Nigel at: http://forums.hardwarezone.com.sg/hardware-clinic-2/%5Bsic%5D-new-setup-corner-all-diy-hardwarezoner-%5E-%5E-3581022.html

 

[BUBUBU]

any1 know how to fix?

 

[moodless]

any1 know how to fix?

with so little details how you expect people to help? lol.

open your casing and make sure all the cables are plugged properly. as one of the members mentioned, other cables might have dropped out while you were removing the GFX.

worst case scenario you never turn off psu and plug out the power cable, your board or psu burnt liao.

gg.com

 

[Magickiller9]

Wa never off psu will burn the board ah?

 

[FlushX]

did you connect your DVI-D/HDMI/Displayport cable to your onboard graphics?

 

[moodless]

Wa never off psu will burn the board ah?

In very suay situations..

 

[ragnarok95]

mean? i already mention wat i did

after i take out the gpu , i just power on again , nvr touch any cable

You take out your video card then you power on.

Of cos there is nothing right?

No?

 

[shadow84]

If u had taken out gpu, did u connect the display cable to the outputs on the mobo? Or just left the cable dangling, not connected to anything on one end?

 

[BUBUBU]

If u had taken out gpu, did u connect the display cable to the outputs on the mobo? Or just left the cable dangling, not connected to anything on one end?

dangling

so?

 

[BUBUBU]

did you connect your DVI-D/HDMI/Displayport cable to your onboard graphics?

no.
.
.
.
did not

 

[hlots123]

vvvery long shot but...
1st try simple off/on psu rocker switch, see if it works;
2nd try off psu, disconnect power cord, then press & hold pc casing power on button for 30sec, then put all back & see if it works...

 

[lowveld]

no.
.
.
.
did not

Wtf? Then how would u expect t see anything bro.

 

[BUBUBU]

Wtf? Then how would u expect t see anything bro.

now cant even on , can see wat