[Help] How to change my LED light on my ceiling fan? Any expert pls advise

[software_developer]

I am using Fanco model
is it possible for me to change the LED light myself, by going to those mama shop and buy?

Which part can I dismantle? I first deal with the ceiling fan light, very worried to unscrew the wrong screw

Only the LED light gt problem

 

[software_developer]

anyone know?......

 

[Laoyeh]

Yr hand so strong can unscrew it

 

[software_developer]

which part can remove?

 

[Cobra!]

Novice here, but I see screws, but you must know how to do soldering to rewire

 

[FinchGuy]

Just replace the LED driver, the white round thing. Buy another with same ratings (wattage, voltage and output current).

 

[software_developer]

But the round thing is connect by another cable on the top? is it must cut?

 

[FinchGuy]

But the round thing is connect by another cable on the top? is it must cut?

Connector at other end probably hidden by LED panel. Pull a bit to expose it or remove the LED panel to access. Make sure new driver has same type of connectors at both ends.

 

[software_developer]

Connector at other end probably hidden by LED panel. Pull a bit to expose it or remove the LED panel to access. Make sure new driver has same type of connectors at both ends.

So I dun need to cut or rewire anything?

i try to pull the connector, it seem very tight

 

[cantona81]

this one cannot buy one...
anyway, how u know is led spoil?

 

[software_developer]

this one cannot buy one...
anyway, how u know is led spoil?

I dk leh, when I on

the light will be very dim...after 30 min, it will fully on

 

[cantona81]

I dk leh, when I on
the light will be very dim...after 30 min, it will fully on

other colour also the same?
will it happen when u switch off and on back immediately?
anyway, could be the driver spoil...

 

[Dolcefarniente]

if no soldering.

cut the blue and grey wire from the fan to the round driver.
then stripe the wire, but a new driver with plug and play LED. re-drill for new mounting.
(the cover will hide all the ugly marks. dun worry)

 

[Miss.Molly]

TS, read this thread:
https://forums.hardwarezone.com.sg/threads/rant-beware-of-fanco-ceiling-fan.5994034/

 

[tankgunner]

try to search on youtube teaching you how to do it.

 

[CCCustom]

KDK fans’ LED light also proprietory connector, spoil must get KDK to replace.

 

[testerjp]

See where the 2 wires connect to.

Else can just strip wire and install a bridge.
The wire has some burn marks though.

 

[foxer77]

KDK fans’ LED light also proprietory connector, spoil must get KDK to replace.

No need Lai just cut off and use connector to diy ...
It not hard ...

 

[MageRav3]

Is your replaceable part connected via magnet?
Nowadays all the LED replacement lights come with driver(That round huge thing).
I walked a few rounds my area hardwareshop, all sell with driver nowadays.
Driverless LED replacement lights no longer selling liao.

You need to take out the driver and leave behind the Live and Neutral wire to connect to the replacement.
The live and neutral wire (to electricity) will go through a connector that looks like this.
Old type uses the nails while new type uses pressure.

Connect the Replacement wires to the live, neutral wire of your lighting fixture using the connector.
I replaced mine a few weeks ago and followed this guide.

 

[software_developer]

See where the 2 wires connect to.

Else can just strip wire and install a bridge.
The wire has some burn marks though.

I dun really understand

so I just cut this one right?