MyRepublic fibre - Part 4

Status
Not open for further replies.

hangyong

Master Member
Joined
May 9, 2002
Messages
3,838
Reaction score
0
Already restore to factory on Monday therefore the router shld be "clean"
for new static ip address. With and without the router MAC address also got limited connection.

follow step by step below and see if each step is ok.
May have to wait for 5-10 mins after each disconnection from ONT to router and also router reboot or setting change for IP to be assigned.

1. connect laptop to ONT port 1 - is it ok?
2. connect ONT port 1 to router WAN port - LED on Asus for Internet for light up?
3. check if DHCP on router is activated, plug cable from port 1 on Asus to laptop - is IP assigned?
 

hangyong

Master Member
Joined
May 9, 2002
Messages
3,838
Reaction score
0
For MR staff..

not from MR, but I had same issue when changed to 1gbps plan... or rather.. its was worst
What happened was the splice in CO is bad or broken and therefore unable to get connection.
was able to sync, meaning connection between me and CO is ok.
unable to connect, meaning connection from within CO most likely.

it took 2 days to find the problem because the problem was not with MR and their equipment was good.

did you change to 1gbps or 300mbps recently?
 

WindJammer

Member
Joined
Jul 7, 2006
Messages
481
Reaction score
2
follow step by step below and see if each step is ok.
May have to wait for 5-10 mins after each disconnection from ONT to router and also router reboot or setting change for IP to be assigned.

1. connect laptop to ONT port 1 - is it ok?
2. connect ONT port 1 to router WAN port - LED on Asus for Internet for light up?
3. check if DHCP on router is activated, plug cable from port 1 on Asus to laptop - is IP assigned?

Just to calrify on the port 1. There is only one port from the balck alcatel ONT right?
 

imacbie

Supremacy Member
Joined
Jul 3, 2004
Messages
6,405
Reaction score
2
what causes the speed to keep on getting bottleneck at 200+ ?
initially, when I reset the router, which is a N66U, speedtest went to normal 900+
few hours later, it will get stuck at 200+, now rebooting doesnt help either
 

bigtux

Member
Joined
Apr 17, 2008
Messages
251
Reaction score
0
The following was posted 27-03-2014, 02:53 PM

Repost again since no response

Status check as we are coming to the end of Mar 2014 ...

C1000345
- was out of contract and then signed up for the 1Gbps deal on 14 Jan 2014
- was informed via the sign-up process that my estimated installation date was 01 Mar 2014 onwards
- have the signup confirmation email from 14 Jan 2014 and relevant screenshots
- no news thereafter

Would appreciate a status update and if possible to email me on the email that you have on record as I don't pop by HWZ daily.

Thank you.
 

hangyong

Master Member
Joined
May 9, 2002
Messages
3,838
Reaction score
0
what causes the speed to keep on getting bottleneck at 200+ ?
initially, when I reset the router, which is a N66U, speedtest went to normal 900+
few hours later, it will get stuck at 200+, now rebooting doesnt help either

you must have made some setting changes...

I tested each setting one by one and found that the traffic monitor is the cause of the slow down.

the only way is to do a factory reset to clear the settings, it will be back to normal... then do the settings again and not do the traffic monitor setting.
 

ithrux

Member
Joined
Feb 21, 2001
Messages
147
Reaction score
0
not from MR, but I had same issue when changed to 1gbps plan... or rather.. its was worst
What happened was the splice in CO is bad or broken and therefore unable to get connection.
was able to sync, meaning connection between me and CO is ok.
unable to connect, meaning connection from within CO most likely.

it took 2 days to find the problem because the problem was not with MR and their equipment was good.

did you change to 1gbps or 300mbps recently?

Nope.

DISABLE STATIC IP
reset router

Static ip was never on, factory reset doesn't solve.

Tried pretty much everything in my arsenal already.
 

imacbie

Supremacy Member
Joined
Jul 3, 2004
Messages
6,405
Reaction score
2
you must have made some setting changes...

I tested each setting one by one and found that the traffic monitor is the cause of the slow down.

the only way is to do a factory reset to clear the settings, it will be back to normal... then do the settings again and not do the traffic monitor setting.

there is no traffic monitoring option.
there is only this graph which cannot be turn off
only to set to real-time or mthly etc.

and now my static is not working.
have to revert to dynamic setting, which essentially is the same ip..
pfft.. i wonder if the cause is the latest firmware of the N66U or the new ONT..
anyway, the new ONT seems slow...
 

hangyong

Master Member
Joined
May 9, 2002
Messages
3,838
Reaction score
0
there is no traffic monitoring option.
there is only this graph which cannot be turn off
only to set to real-time or mthly etc.

and now my static is not working.
have to revert to dynamic setting, which essentially is the same ip..
pfft.. i wonder if the cause is the latest firmware of the N66U or the new ONT..
anyway, the new ONT seems slow...

on your ONT what is the speed you are getting?

your router, try to flash to rmerlin's latest firmware instead of asus'.

DO not set to static IP in the router. Leave it at DHCP mode. You will be assigned your static IP automatically.
 

imacbie

Supremacy Member
Joined
Jul 3, 2004
Messages
6,405
Reaction score
2
on your ONT what is the speed you are getting?

your router, try to flash to rmerlin's latest firmware instead of asus'.

DO not set to static IP in the router. Leave it at DHCP mode. You will be assigned your static IP automatically.
had gotten 900+ from ONT
900+ from router also.. but it dropped and stuck
i'm on merlin since the day i got my router bout a yr ago? lol
i dun understand why the static option is not working since they are essentially the same ip
 

WindJammer

Member
Joined
Jul 7, 2006
Messages
481
Reaction score
2
I have no idea man... I am using the one with the voice which has 4 ports...

If i enter the static ip address, do i have to enter the subnet mask, gateway, pri and sec dns, mac address???? are these value standard across all MR subscriber except the static ip address?
 

hangyong

Master Member
Joined
May 9, 2002
Messages
3,838
Reaction score
0
had gotten 900+ from ONT
900+ from router also.. but it dropped and stuck
i'm on merlin since the day i got my router bout a yr ago? lol
i dun understand why the static option is not working since they are essentially the same ip

on 374.40?

this one is because of a change in setting backend.
The authentication is no longer with MAC of router but rather on the ONT itself.

just leave everything in auto mode.
 

Just Me

Arch-Supremacy Member
Joined
Jan 1, 2000
Messages
14,249
Reaction score
41
on 374.40?

this one is because of a change in setting backend.
The authentication is no longer with MAC of router but rather on the ONT itself.

just leave everything in auto mode.

So you mean that you no longer need your router mac address for the static ip?
 

abbnic

Junior Member
Joined
Aug 17, 2012
Messages
37
Reaction score
0
Connected to Wireless network but not connected to internet

My problem with MR's new 1Gbps plan:
Connected to Wireless network but not connected to internet

Anyone encounter similar issue? I am using an old HP AIO running Windows Vista.
My other devices, laptop, ipads, phones all connected with no issues. (I dont have a lan connection, all wireless devices)

Could not update the firmware over wifi, so may try to download from Asus and install. Any other firmware i should try instead.

Appreciate any help, thanks.
 

playboysg

Member
Joined
Jul 1, 2005
Messages
395
Reaction score
0
on your ONT what is the speed you are getting?

your router, try to flash to rmerlin's latest firmware instead of asus'.

DO not set to static IP in the router. Leave it at DHCP mode. You will be assigned your static IP automatically.

hi bro, i am using ASUS AC56U.

What do you meant by rmerlin firmware?

Thanks.
 
Status
Not open for further replies.
Important Forum Advisory Note
This forum is moderated by volunteer moderators who will react only to members' feedback on posts. Moderators are not employees or representatives of HWZ Forums. Forum members and moderators are responsible for their own posts. Please refer to our Community Guidelines and Standards and Terms and Conditions for more information.
Top