M1 FIBRE BROADBAND DISCUSSION - Part 2

[kelvinti]

Oh well! Unfortunately, my 7 years old Asus pc has a 100mbps only ethernet port.

So, the best way is to stick to my wireless adapter which has a max of 866mbps as an AC1300 model.

My Asus pc is located inside my bedroom and most of time my room door is closed. My Asus pc is capable of running at 480mbps to 550mbps with the help of the wireless adapter via my USB 3.1 port at least.

Without the help of the wireless adapter. The Asus onboard PCI E wireless port can't even get connected to 5Ghz even with my bedroom door wide opened!

 

[unrealx262]

just recon 1gb with m1 and got these speeds. run speedtest on my iphone 14 in front of the router ax5400 at 7pm earlier. would this be rightful speed to get from this plan's speed?

 

[kelvinti]

just recon 1gb with m1 and got these speeds. run speedtest on my iphone 14 in front of the router ax5400 at 7pm earlier. would this be rightful speed to get from this plan's speed?

2.4Ghz or 5Ghz speed test?

Surely cannot be that low speed! May be your BB has not been optimized by the M1 backend infra yet which usually happens over the night.

Personally, I stick to 5Ghz on my Samsung phone. I don't use 2.4Ghz.

My Samsung Wifi6 capable phone can achieve up to 400-500mpbs on 5Ghz next to the router with the phone WiFi connection statistic shows a whopping 1.2Gbps connection on 5Ghz.

I suggest you safari to the official M1 BB speed test by M1 itself and do the test on your iPhone. Don't use any 3rd party app or website to run the speed test. The same on your Macbook or PC.

https://www.m1.com.sg/home-broadband/speed-test

 

[newsera]

Anyone has working config for IPv6 on M1 Broadband? Router: Ubiquiti / USG / Edgerouter
eth0=WAN
switch0=LAN

Tried the below, but no luck

set interfaces ethernet eth0 dhcpv6-pd pd 0 interface switch0 host-address ::1
set interfaces ethernet eth0 dhcpv6-pd pd 0 interface switch0 service slaac
set interfaces ethernet eth0 dhcpv6-pd pd 0 prefix-length /64

set interfaces ethernet eth0 dhcpv6-pd pd 0 interface switch0 prefix-id :0
set interfaces ethernet eth0 dhcpv6-pd rapid-commit enable

 

[PinkGlory]

it's been like that in the past. the renewal window opens a few months before end of contract. a renewal charge applies if you renew before, as you experienced.

How much would be the early renewal charge? I thought they offer to subscribers as an incentive.

 

[bexar]

it's been like that in the past. the renewal window opens a few months before end of contract. a renewal charge applies if you renew before, as you experienced.

My situation is that I had renewed exactly on one day after four months before the expiry date. The "excess" charge is the same as the termination charge. It looks like they made a mistake of terminating my old plan. I am still following up with them.

 

[bexar]

How much would be the early renewal charge? I thought they offer to subscribers as an incentive.

I think it's a mistake. The "early renewal" charge is the same amount as the termination charge for 4 months before the expiry date. I am following up with them.

 

[PinkGlory]

I called M1. Customer service told be no charges for early recontract. I am still undecided which router to get. Or to redeem later.

 

[unrealx262]

2.4Ghz or 5Ghz speed test?

Surely cannot be that low speed! May be your BB has not been optimized by the M1 backend infra yet which usually happens over the night.

Personally, I stick to 5Ghz on my Samsung phone. I don't use 2.4Ghz.

My Samsung Wifi6 capable phone can achieve up to 400-500mpbs on 5Ghz next to the router with the phone WiFi connection statistic shows a whopping 1.2Gbps connection on 5Ghz.

I suggest you safari to the official M1 BB speed test by M1 itself and do the test on your iPhone. Don't use any 3rd party app or website to run the speed test. The same on your Macbook or PC.

https://www.m1.com.sg/home-broadband/speed-test

use m1 just now and tested.

 

[xsoldix]

use m1 just now and tested.

try restart both your devices ..

and call m1 ask them reset on their backend.

 

[crystalnox]

use m1 just now and tested.

I'm sorry but your speedtests just tells us that your wifi router speeds suck. Your 1gbps plan is completely wasted if that's all the speed your wifi can get, might as well downgrade plan.

This is my speedtest on M1's 500mbps plan on PC and phone (both on wifi):

 

[Youmigratecanotherscant]

What’s the cheapest home broadband from m1

 

[Mach3.2]

What’s the cheapest home broadband from m1

https://www.imda.gov.sg/-/media/imd...r-education/home-access/ha20-direct-appv4.pdf

 

[Youmigratecanotherscant]

https://www.imda.gov.sg/-/media/imd...r-education/home-access/ha20-direct-appv4.pdf

Haiz. Can’t qualify Liao. $30 is ok. But all internet seller is charging activation or other extra charges.

 

[loganrunning]

How much would be the early renewal charge? I thought they offer to subscribers as an incentive.

sorry, i can't remember the figure i was quoted a few years ago. Just that it was enough to deter me from early recontract - the penalty was more than the savings from the promo rate - somehow my recontract window is always out of synch with their promos. Anyway, moved to 500Mbps and no more promo recontract anxiety.

 

[loganrunning]

I called M1. Customer service told be no charges for early recontract. I am still undecided which router to get. Or to redeem later.

their policies keep changing..... on a positive side, responding to the market (hopefully they now value existing subscribers)

 

[unrealx262]

I'm sorry but your speedtests just tells us that your wifi router speeds suck. Your 1gbps plan is completely wasted if that's all the speed your wifi can get, might as well downgrade plan.

This is my speedtest on M1's 500mbps plan on PC and phone (both on wifi):

what router are u using? im using their stock tp link ax5400

this is my eternet speed btw. which seems ok.. prob the wifi channels are congested or router wifi setting ?

 

[crystalnox]

what router are u using? im using their stock tp link ax5400

this is my eternet speed btw. which seems ok.. prob the wifi channels are congested or router wifi setting ?

Try changing your 5Ghz channels and retest.

 

[unrealx262]

dl ul
2.4 1 71.1 79.9
2 88.5 99.5
3 110.3 123
4 135.4 129.3
5 121 64.8
6 86.6 95.6
7 104.6 87.7
8 123.9 82.3
9 81.6 59
10 83.6 87
11 96.6 77

Try changing your 5Ghz channels and retest.

based on the results.

		dl	ul
5ghz	auto	197.3​	165.3​
	36​	210.3​	222.3​
	40​	215.9​	221.8​
	44​	214.6​	223.7​
	48​	214.2​	209.7​
	149​	204.5​	208.3​
	153​	195​	196.2​
	157​	206.9​	219.6​
	161​	215.4​	218.1​
	165​	201.1​	198.3​
		dl	ul
2.4ghz​	1​	71.1​	79.9​
	2​	88.5​	99.5​
	3​	110.3​	123​
	4​	214.2​	221​
	5​	121​	64.8​
	6​	86.6​	95.6​
	7​	104.6​	87.7​
	8​	123.9​	82.3​
	9​	81.6​	59​
	10​	83.6​	87​
	11​	96.6​	77​

 

[crystalnox]

based on the results.

		dl	ul
5ghz	auto	197.3​	165.3​
	36​	210.3​	222.3​
	40​	215.9​	221.8​
	44​	214.6​	223.7​
	48​	214.2​	209.7​
	149​	204.5​	208.3​
	153​	195​	196.2​
	157​	206.9​	219.6​
	161​	215.4​	218.1​
	165​	201.1​	198.3​

Wah that is awfully low considering your router is 4T4R Wifi6. Try setting your channel width to 80Mhz, security set to WPA2/WPA3-Personal and OFDMA set to On in Advance settings.