[CASE] Phanteks Enthoo EVOLV ATX

[Gattberserk]

then can help link us up? lol.

i okay with the price. last time you shared with them they dont know the price or know already still bargain? if know already still bargain very wtf sia lol.

Yup I would be very interested to cut a hole for my top panel if needed.

 

[Cedesria]

wheres your fan extensions and also the phantek velcros?

All hidden from sight. I did not even use the supplied fan hub.

 

[Gattberserk]

wheres your fan extensions and also the phantek velcros?

The velcros can be seem below the 24 pins cables.


Anyway I am planning to take one big black vanguard sheet, cut it to the Rear panel size and just mask over. At most I will do a cut out for the sheet to display the SSD like the mATX version.

 

[ricoreload]

Agreed. Non tempered glass no need care about the cable management at the rear case. For the tempered glass version, if u are OCD like me you will want to cable manage Swee Swee

My rear panel cable management.


Top Panel Vents Machined Water Jet Cut


You can see the cut surface is in raw Alu state, if your case is black, it will be obvious. Mine is grey case and being an OCD, I decided to go powder coat. Alternative one can choose to go anodized it again but the cost would easily hit $200 plus

Wow! U cut it urself?

Sent from Xiaomi MI MAX using GAGT

 

[Cedesria]

Wow! U cut it urself?

Sent from Xiaomi MI MAX using GAGT

Cut myself? No, I had the help of the waterjet cutting machine haha. Drawn them in Autocad and sent them to cut.

 

[hg_wng]

Cut myself? No, I had the help of the waterjet cutting machine haha. Drawn them in Autocad and sent them to cut.

Do you mind sharing your design? Looks really good, interested to the difference in temps.

 

[Cedesria]

Just collected my newly powder coated and newly cut vent holes panel. Go home tonight then go through the whole lot

 

[joshuaho]

Where u send to do waterjet cutting?

Cut myself? No, I had the help of the waterjet cutting machine haha. Drawn them in Autocad and sent them to cut.

 

[Cedesria]

Where u send to do waterjet cutting?

A friend's workshop

 

[Cedesria]

Screwed back the plastic parts back to the panels. The powder coats are good. No more finger prints magnets!

 

[Cedesria]

Fixed back all the panels back into the frame. Now left with my perforated sheets.

 

[evq]

Agreed. Non tempered glass no need care about the cable management at the rear case. For the tempered glass version, if u are OCD like me you will want to cable manage Swee Swee

My rear panel cable management.

The best cable management I have seen. Tot I was doing ok with my cables, feeling proud 2 days back when i redo my cables. This pic put me into shame. hahahah.

btw, may i know how many hdd, ssd did u install? Ur cables are a lot lesser than mine.

Can u show the other side of ur pc? damn chio

 

[Cedesria]

The best cable management I have seen. Tot I was doing ok with my cables, feeling proud 2 days back when i redo my cables. This pic put me into shame. hahahah.

btw, may i know how many hdd, ssd did u install? Ur cables are a lot lesser than mine.

Can u show the other side of ur pc? damn chio

Total 2 X HDD, 3 X 2.5 inch SSD, 1 X m.2 SSD

 

[LionPlushie]

The best cable management I have seen. Tot I was doing ok with my cables, feeling proud 2 days back when i redo my cables. This pic put me into shame. hahahah.

btw, may i know how many hdd, ssd did u install? Ur cables are a lot lesser than mine.

Can u show the other side of ur pc? damn chio

cause he route thru the back. mine all thru the center pods lol but i using windowed and not tempered glass so is solid panel

@cedesria your powder coat total how much ar? thinking if i should send mine for powder coat. but mine will be more expensive cause got 2 side panels.. maybe cheaper to just buy a new one

anyway your temperature got improve?

 

[xtractor]

Total 2 X HDD, 3 X 2.5 inch SSD, 1 X m.2 SSD

i still suggest u watercooling ur system that gtx 1080 SLI heat with those temp run @ 90°++C is "killing" u
and look nicer when u WC it

 

[Cedesria]

i still suggest u watercooling ur system that gtx 1080 SLI heat with those temp run @ 90°++C is "killing" u
and look nicer when u WC it

Actually going back to wc. My bitspower blocks are arriving on Monday.

Bending kit ready, going copper pipe bending.


My bitspower fittings also ready,


My bitspower res and pump also Ready. My bitspower straight copper nickel tubes and my alphacool radiators also just arrived. So now just waiting for my bitspower gpu and cpu blocks, bitspower d5 res connector cover to arrive.

Since all cable management done, rest of the job is very easy. Leak test, and flush the rads and fix up only. Just that the bended copper tubes have to send for nickel plating.

Quite excited actually, I tried fixing my silver shiny bitspower fittings to the chrome pipes are damn sick looking.

 

[Cedesria]

cause he route thru the back. mine all thru the center pods lol but i using windowed and not tempered glass so is solid panel

@cedesria your powder coat total how much ar? thinking if i should send mine for powder coat. but mine will be more expensive cause got 2 side panels.. maybe cheaper to just buy a new one

anyway your temperature got improve?

Cpu and gpu bottom card did improved. But the top gpu temps lowered a bit only 2-4 degrees lower. But can't help, it is starved of cool fresh air. So if i wc, temps confirm will be lowered. Powder coat spent around $150.

 

[NeonX]

Sli you’re running 90+

Omg, I’m gonna sli later also gg

Sent from Samsung SM-G955F using GAGT

 

[NeonX]

All hidden from sight. I did not even use the supplied fan hub.

how you manage to route so cleanly sia. My 3 fans in front + sata molex cable all those i can only route through the middle

 

[Cedesria]

how you manage to route so cleanly sia. My 3 fans in front + sata molex cable all those i can only route through the middle

Mine all using latest tech, all wireless powered! muahahahha