Opennet installion - share experience please

[Mach3.2]

Later i go dig mine.

1310nm: 0.69
1490nm: 0.55
1550nm: 0.*2(Dun even understand what he wrote down..)

1310: 0.78
1490: 0.71
1550: 0.63

this mine. higher better or lower?

Lower better.

Below is mine reading for singtel

1310nm: 0.30
1490nm: 0.33
1550nm: 0.39

Is this good or bad?

Welly koot.

 

[Alpha0]

1310nm: 0.61
1490nm: 0.59
1550nm: 0.31

actually what are these 3 measurements for ?
does these measurements affect the fibre connection greatly ?

thanks

 

[raylite]

1310nm: 0.97
1490nm: 0.87
1550nm: 0.77

Mine seems bad

 

[ideatalk]

what can u do if the number is high or low?

 

[Mach3.2]

what can u do if the number is high or low?

llst.
It's still within industrial standards..

 

[socrates]

yes what do these numbers represent?

 

[Mach3.2]

yes what do these numbers represent?

Google will you?

Its something about signal iirc.

 

[boontiong]

Installed on last sat and tested yesterday.

1310 - 0.33
1490 - 0.28
1550 - 0.20

 

[ideatalk]

r we going to shoot the opennet ppl if the number is not right?
or just depend on the surfing speed after we subscribe with the ISP?

 

[liangtam]

r we going to shoot the opennet ppl if the number is not right?
or just depend on the surfing speed after we subscribe with the ISP?

How do you know the number are right or not in the first place? If any, the number stated are within acceptable range when signing off. If you based on BW, it could be because your RSP is screwy/provide crap service OR because due to the RSP agreement say nucleus connect only provide rate of say 25mbps guaranteed bandwidth they got away with just providing the bare minimum rate under contractual agreement, how to determine?

 

[ideatalk]

is there a standard number that we can refer to as most of us is not so savvy.
when the ONT and router is installed how do we know the number is still ok?

 

[ideatalk]

this 3M mini stuff is at least an alternative i hope

till can get fibre in my area..

what is the 3M mini thing like? can advise? i m curious to learn.

 

[ideatalk]

Now Opennet is suing ppl means they dont have to speed up the installation and clear the backlog?

 

[Mach3.2]

what is the 3M mini thing like? can advise? i m curious to learn.

One Pass

Basically it's the relocation of FTP, you need to have the FTP installed, if not, it's useless.

 

[ideatalk]

recently my friends installing the TP have no problem in asking the opennet guys to install in the location they prefer.
Has their policy changed or the guys become smarter to avoid any arguement with customers

 

[liangtam]

recently my friends installing the TP have no problem in asking the opennet guys to install in the location they prefer.
Has their policy changed or the guys become smarter to avoid any arguement with customers

It depends on the individual contractors, nothing with the policy.

 

[techrike]

will the opennet guys do the cat5e/6 cable wiring for you as well? or must get own contractor to do it?

 

[chengsun]

will the opennet guys do the cat5e/6 cable wiring for you as well? or must get own contractor to do it?

no they will not, u need own contractor. but probably u can ask the technicians if they want to do part time.

 

[techrike]

no they will not, u need own contractor. but probably u can ask the technicians if they want to do part time.

thx bro. so means for living room and bedroom to have connection is to connect using cat5e/6 cable right. dun need to have 2 TP?

and also would like to check if the current starhub tv point is the cat5e/6 junction point?

 

[ideatalk]

thx bro. so means for living room and bedroom to have connection is to connect using cat5e/6 cable right. dun need to have 2 TP?

and also would like to check if the current starhub tv point is the cat5e/6 junction point?

if u just want to run a cat5e cable from tp in living room to bedroom the ISP can do for free just like mine......
the present tv point is using co-axial cable